- 您現在的位置：買賣IC網 > PDF目錄383986 > USB97C243 (SMSC Corporation) capacitor Selection for Internal Regulator Output Pins PDF資料下載
參數資料
| 型號： | USB97C243 |
| 廠商： | SMSC Corporation |
| 英文描述： | capacitor Selection for Internal Regulator Output Pins |
| 中文描述： | 電容的選擇內部穩壓器輸出引腳 |
| 文件頁數： | 31/59頁 |
| 文件大?。?/td> | 385K |
| 代理商： | USB97C243 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
SMSC DS – USB97C201
Page 31
Rev. 03/25/2002
PRELIMINARY
Table 28 – SIE Status Register
SIE_STAT
(0xB0 - RESET=0x00)
NAME
SET_STALL
SIE STATUS REGISTER
DESCRIPTION
BIT
[7]
R/W
R/W
Set to “1” if a SET_FEATURE_ENDPOINT_HALT command
is received on any endpoint by the SIE. Which endpoint is
STALLed can be determined by examining their CTL
registers.
Set to “1” if a CLEAR_FEATURE_ENDPOINT_HALT
command is received on any endpoint by the SIE. Which
endpoint’s STALL condition is cleared can be determined
by examining their CTL registers.
Set to “1” if a SET_CONFIGURATION command is received
on endpoint 0 by the SIE and the resulting configuration is
set and reported in the USB_CONFIG register.
This read only bit always returns the value of “0”.
Set to “1” if a SET_INTERFACE command is received on
endpoint 0 by the SIE.
This read only bit always returns the value of “0”.
Set to “1” if a SET_FEATURE_REMOTE_WAKE_UP
command is received on endpoint 0 by the SIE.
Set
to
CLEAR_FEATURE_ENDPOINT_REMOTE_WAKE_UP
command is received on endpoint 0 by the SIE.
6
CLR_STALL
R/W
5
SET_CONF
R/W
4
3
Reserved
SET_INTF
R
R/W
2
1
Reserved
SET_REMWU
R-
R/W
0
CLR_REMWU
R/W
“1”
if
a
Note:
These bits are masked by the SIE_MSK register and OR’d to drive the INT3 interrupt line into the 8051 core.
They may be cleared writing a “1” to the bit location.
Table 29 – SIE Status Mask Register
SIE_MSK
(0xAE - RESET=0xFF)
NAME
SET_STALL
SIE STATUS MASK REGISTER
DESCRIPTION
1= Disable interrupt generation.
0= Enable interrupt generation.
1= Disable interrupt generation.
0= Enable interrupt generation.
1= Disable interrupt generation.
0= Enable interrupt generation.
This read only bit always returns the value of “1”.
1= Disable interrupt generation.
0= Enable interrupt generation.
This read only bit always returns the value of “1”.
1= Disable interrupt generation.
0= Enable interrupt generation.
1= Disable interrupt generation.
0= Enable interrupt generation.
BIT
[7]
R/W
R/W
6
CLR_STALL
R/W
5
SET_CONF
R/W
4
3
Reserved
SET_INTF
R
R/W
2
1
Reserved
SET_REMWU
R
R/W
0
CLR_REMWU
R/W
Note:
The mask bits do not prevent the status in the SIE_STAT register from being set, only from driving the INT3
line of the 8051 core high.
相關PDF資料 |
PDF描述 |
|---|---|
| USB97CFDC | USB FLOPPY DISK CONTROLLER |
| USH-1000-KS | Lamps for Photolithography |
| USH1000FAL2 | Lamps for Photolithography |
| USH1002FGL | Lamps for Photolithography |
| USH1002FNIL2 | Lamps for Photolithography |
相關代理商/技術參數 |
參數描述 |
|---|---|
| USB97C243-JN-04 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| USB97CFDC | 制造商:SMSC 制造商全稱:SMSC 功能描述:USB FLOPPY DISK CONTROLLER |
| USB97CFDC2-01 | 制造商:SMSC 制造商全稱:SMSC 功能描述:USB Floppy Disk Controller |
| USB97CFDC2-MN-01 | 功能描述:USB 接口集成電路 USB Floppy Disk CNTRL RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| USB97CFDC2-MV-01 | 功能描述:USB 接口集成電路 USB Floppy Disk CNTRL RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。