參數資料
型號： UPD17242UC-XXX-5A4
元件分類： 微控制器/微處理器
英文描述： 4-BIT, MROM, 4.5 MHz, MICROCONTROLLER, PDSO30
封裝： 0.300 INCH, PLASTIC, SSOP-30
文件頁數： 60/102頁
文件大?。?/td> 953K
代理商： UPD17242UC-XXX-5A4
60
Data Sheet U15002EJ1V1DS
PD17240, 17241, 17242, 17243, 17244, 17245, 17246
7.
RAM RETENTION DETECTOR
7.1
RAM Retention Flag
The RAM retention flag (bit 0 of the register file at address 21H) indicates whether the supply voltage has dropped
below the level at which the contents of the RAM are lost while the battery is being exchanged or when the battery
voltage has dropped.
This flag is at bit 3 of control register 0 (P3).
It is cleared to 0 if the supply voltage drops below the RAM retention detection voltage (approx. 1.4 V TYP.). If
this flag is 0, it can be judged that the RAM contents have been lost or that power has just been applied. This flag
can be used to initialize the RAM via software. After initializing the RAM and writing the necessary data to it, set this
RAM retention flag to “1” by software. At this time, 1 means that data has been set to the RAM.
Figure 7-1. Supply Voltage Transition and Detection Voltage
VDD
VPOC
VID
0 V
RAM retention flag
(A)
(B)
(6)
(5)
(4)
(3)
(2)
Set to 1
Flag content is read.
(1)
t
POC detection voltage
VPOC = 1.85 V (TYP.)
RAM retention detection voltage
VID = 1.4 V (TYP.)
(1) If the supply voltage rises after the battery has been set, and exceeds VPOC (POC detection voltage), reset
is cleared. Because the supply voltage rises from 0 V, which is lower than VID (RAM retention detection
voltage), the RAM retention flag remains in the initial status 0.
(2) The supply voltage has now risen to the level at which the device can operate. Write the necessary data to
the RAM and set the RAM retention flag to 1.
(3) The device is reset if the supply voltage drops below VPOC. At point (A) in the above figure, the RAM retention
flag remains 1 because the supply voltage is higher than VID at this point.
(4) If the RAM retention flag is checked by software after reset has been cleared, it is 1. This means that the
contents of the RAM have not been lost. It is therefore not necessary to initialize the RAM by software.
(5) The device is reset if the supply voltage drops below VPOC. At point (B) in the figure, the voltage is lower than
VID. Consequently, the RAM retention flag is cleared to 0.
(6) If the RAM retention flag is checked by software after reset has been cleared, it is 0. This means that the
contents of the RAM may have been lost. If this happens, initialize the RAM by software.
相關PDF資料
PDF描述
UPD178F054 78K/0 Series for Instructions | User＇s Manual[10/2001]
UPD178F124 78K/0 Series for Instructions | User＇s Manual[10/2001]
UPD178F098GF-3BA-A 8-BIT, FLASH, MICROCONTROLLER, PQFP100
UPD17P136BGT MICROCONTROLLER, PDSO28
UPD1913C Consumer IC
相關代理商/技術參數
參數描述
UPD17243 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLERS FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTERS
UPD17243MC-XXX-5A4 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLERS FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTERS
UPD17244 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLERS FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTERS
UPD17244MC-XXX-5A4 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLERS FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTERS
UPD17245 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLERS FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTERS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*