參數資料
型號： TPS65185RSLT
廠商： TEXAS INSTRUMENTS INC
元件分類： 電源管理
英文描述： POWER SUPPLY SUPPORT CKT, PQCC48
封裝： 6 X 6 MM, 0.4 MM PITCH, 0.9 MM HEIGHT, PLASTIC, VQFN-48
文件頁數： 10/49頁
文件大?。?/td> 2488K
代理商： TPS65185RSLT
PRODUCTPREVIEW
VIN
PWRUP
WAKEUP
VNEG
VEE
VPOS
VDDH
PWR_GOOD
VN
VB
1.8ms
(1)
DDLY 2
DDLY 3
DDLY 4
DDLY 1
300 us (max)
STANDBY
ACTIVE
SLEEP
ACTIVE
(1) Minimum delay time between WAKEUP rising edge and IC rady to accept I 2C transaction .
UDLY 2
UDLY 3
UDLY 1
UDLY 4
I2C
300 us (max)
UDLY 2
UDLY 1
UDLY 4
UDLY 3
Discharge Delay
SLVSAQ8A
– FEBRUARY 2011 – REVISED MAY 2011
In this example the first power-up sequence is started by pulling the PWRUP pin high (rising edge). Power-down is
initiated by pulling the WAKEUP pin low (device enters SLEEP mode). The 2nd power-up sequence is initiated by
pulling the WAKEUP pin high while the PWRUP pin is also high (power up from SLEEP to ACTIVE).
Figure 24. Power-Up and Power-Down Timing Diagram
SOFTSTART
TPS65185 supports soft-start for all rails, i.e. inrush current is limited during startup of DCDC1, DCDC2, LDO1,
LDO2, CP1 and CP2. If DCDC1 or DCDC2 are unable to reach power-good status within 50 ms, the
corresponding UV flag is set in the interrupt registers, the interrupt pin is pulled low, and the device enters
STANDBY mode. LDO1, LDO2, positive and negative charge pumps also have a 50-ms power-good time-out
limit. If either rail is unable to power up within 50 ms after it has been enabled, the corresponding UV flag is set
and the interrupt pin is pulled low. However, the device will remain in ACTIVE mode in this case.
ACTIVE DISCHARGE
TPS65185 provides low-impedance discharge paths for the display power rails (VEE, VNEG, VPOS, VDDH, and
VCOM) which are enabled whenever the corresponding rail is disabled. The discharge paths are connected to
the rails on the PCB which allows adding external resistors to customize the discharge time. However, external
resistors are not required.
Active discharge remains enabled for 100 ms after the last rail has been disabled (STROBE4 has been
executed). During this time the negative boost converter (VN) remains up. After the discharge delay, VN is shut
down and the device enters STANDBY or SLEEP mode, depending on the state of the WAKEUP pin.
18
Copyright
2011, Texas Instruments Incorporated
相關PDF資料
PDF描述
TPS65200YFFR 1-CHANNEL POWER SUPPLY SUPPORT CKT, BGA36
TPS65251RHAT SWITCHING REGULATOR, PQCC40
TPS65251RHAR SWITCHING REGULATOR, PQCC40
TPS65257RHAT 4 A SWITCHING REGULATOR, 2200 kHz SWITCHING FREQ-MAX, PQCC40
TPS65510RGTRG4 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16
相關代理商/技術參數
參數描述
TPS65186RGZR 功能描述:其他電源管理 PMIC FOR E-INK PAPER DISPLAY RoHS:否 制造商:Texas Instruments 輸出電壓范圍: 輸出電流:4 mA 輸入電壓范圍:3 V to 3.6 V 輸入電流: 功率耗散: 工作溫度范圍:- 40 C to + 110 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-48 封裝:Reel
TPS65186RGZT 功能描述:LCD Gamma緩沖器 PMIC FOR E-INK PAPER DISPLAY RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube
TPS65190RHDR 功能描述:LCD 驅動器 10Ch Level Shifter for LCD Displays RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
TPS65191RHBR 功能描述:LCD 驅動器 7Ch Level Shifter for LCD Displays RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
TPS65192RHDR 功能描述:LCD 驅動器 9Ch Level Shifter for LCD Displays RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*