參數資料
型號： TMS320C6701GGP100
廠商： Texas Instruments, Inc.
元件分類： 數字信號處理
英文描述： FIXED-POINT DIGITAL SIGNAL PROCESSOR
中文描述： 定點數字信號處理器
文件頁數： 29/70頁
文件大?。?/td> 1050K
代理商： TMS320C6701GGP100
TMS320C6205
FIXED-POINT DIGITAL SIGNAL PROCESSOR
SPRS106E
OCTOBER 1999
REVISED MARCH 2004
29
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251
1443
triggering, wake-up, and effects
The power-down modes and their wake-up methods are programmed by setting the PWRD field (bits 15
10)
of the control status register (CSR). The PWRD field of the CSR is shown in Figure 8 and described in Table 5.
When writing to the CSR, all bits of the PWRD field should be set at the same time. Logic 0 should be used when
“writing” to the reserved bit (bit 15) of the PWRD field. The CSR is discussed in detail in the
TMS320C6000 CPU
and Instruction Set Reference Guide
(literature number SPRU189).
31
16
15
14
13
12
11
10
9
8
Reserved
Enable or
Non-Enabled
Interrupt Wake
Enabled
Interrupt Wake
PD3
PD2
PD1
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
7
0
Legend:
R/W
x = Read/write reset value
NOTE: The shadowed bits are not part of the power-down logic discussion and therefore are not covered here. For information on these other
bit fields in the CSR register, see the
TMS320C6000 CPU and Instruction Set Reference Guide
(literature number SPRU189).
Figure 8. PWRD Field of the CSR Register
Power-down mode PD1 takes effect eight to nine clock cycles after the instruction that sets the PWRD bits in the
CSR.
If PD1 mode is terminated by a non-enabled interrupt, the program execution returns to the instruction where PD1
took effect. If PD1 mode is terminated by an enabled interrupt, the interrupt service routine will be executed first,
then the program execution returns to the instruction where PD1 took effect. The GIE bit in CSR and the NMIE
bit in the interrupt enable register (IER) must also be set in order for the interrupt service routine to execute;
otherwise, execution returns to the instruction where PD1 took effect upon PD1 mode termination by an enabled
interrupt.
PD2 and PD3 modes can only be aborted by device reset. Table 5 summarizes all the power-down modes.
相關PDF資料
PDF描述
TMS320C6701GHK100 FIXED-POINT DIGITAL SIGNAL PROCESSOR
TMS320C6701GJC100 FIXED-POINT DIGITAL SIGNAL PROCESSOR
TMS320C6701GJL100 FIXED-POINT DIGITAL SIGNAL PROCESSOR
TMS320C6701GLS100 FIXED-POINT DIGITAL SIGNAL PROCESSOR
TMS320C6701GLW100 FIXED-POINT DIGITAL SIGNAL PROCESSOR
相關代理商/技術參數
參數描述
TMS320C6701GJC150 功能描述:數字信號處理器和控制器 - DSP, DSC Floating-Pt Dig Sig Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320C6701GJC167 制造商:TI 功能描述:Refurbished
TMS320C6701GJCA120 功能描述:數字信號處理器和控制器 - DSP, DSC Floating-Point Dig Signal Proc RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
TMS320C6711BFGNA100 制造商: 功能描述: 制造商:undefined 功能描述:
TMS320C6711BGFN100 功能描述:IC FLOATING-POINT DSP 256-BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:TMS320C67x 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*