參數資料
型號： TLV320AIC31IRHBT
廠商： TEXAS INSTRUMENTS INC
元件分類： 消費家電
英文描述： SPECIALTY CONSUMER CIRCUIT, PQCC32
封裝： 5 X 5 MM, GREEN, PLASTIC, QFN-32
文件頁數： 10/83頁
文件大?。?/td> 1197K
代理商： TLV320AIC31IRHBT
SDA
SCL
t
HD-STA
2.0
s
m
t
SU-STO
2.0
s
m
P
S
t
SU-STA
2.0
s
m
Sr
t
HD-STA
2.0
s
m
S
T0114-02
SLAS497C – AUGUST 2006 – REVISED DECEMBER 2008 ............................................................................................................................................. www.ti.com
Figure 15. I2C Interface Timing
Communication on the I2C bus always takes place between two devices, one acting as the master and the other
acting as the slave. Both masters and slaves can read and write, but slaves can only do so under the direction of
the master. Some I2C devices can act as masters or slaves, but the TLV320AIC31 can only act as a slave
device.
An I2C bus consists of two lines, SDA and SCL. SDA carries data; SCL provides the clock. All data are
transmitted across the I2C bus in groups of eight bits. To send a bit on the I2C bus, the SDA line is driven to the
appropriate level while SCL is LOW (a LOW on SDA indicates the bit is '0'; a HIGH indicates the bit is '1'). Once
the SDA line has settled, the SCL line is brought HIGH, then LOW. This pulse on SCL clocks the SDA bit into the
receiver shift register.
The I2C bus is bidirectional: the SDA line is used both for transmitting and receiving data. When a master reads
from a slave, the slave drives the data line; when a master sends to a slave, the master drives the data line.
Under most circumstances the master drives the clock line.
Most of the time the bus is idle; no communication takes place, and both lines are HIGH. When communication is
taking place, the bus is active. Only master devices can start a communication. They do this by causing a
START condition on the bus. Normally, the data line is only allowed to change state while the clock line is LOW.
If the data line changes state while the clock line is HIGH, it is either a START condition or its counterpart, a
STOP condition. A START condition is when the clock line is HIGH and the data line goes from HIGH to LOW. A
STOP condition is when the clock line is HIGH and the data line goes from LOW to HIGH.
After the master issues a START condition, it sends a byte that indicates which slave device it wants to
communicate with. This byte is called the address byte. Each device on an I2C bus has a unique 7-bit address to
which it responds. (Slaves can also have 10-bit addresses; see the I2C specification for details.) The master
sends an address in the address byte, together with a bit that indicates whether it wishes to read from or write to
the slave device.
Every byte transmitted on the I2C bus, whether it is address or data, is acknowledged with an acknowledge bit.
When a master has finished sending a byte (eight data bits) to a slave, it stops driving SDA and waits for the
slave to acknowledge the byte. The slave acknowledges the byte by pulling SDA LOW. The master then sends a
clock pulse to clock the acknowledge bit. Similarly, when a master has finished reading a byte, it pulls SDA LOW
to acknowledge this to the slave. It then sends a clock pulse to clock the bit.
A not-acknowledge is performed by simply leaving SDA HIGH during an acknowledge cycle. If a device is not
present on the bus, and the master attempts to address it, it will receive a not-acknowledge because no device is
present at that address to pull the line LOW.
When a master has finished communicating with a slave, it may issue a STOP condition. When a STOP
condition is issued, the bus becomes idle again. A master may also issue another START condition. When a
START condition is issued while the bus is active, it is called a repeated START condition.
18
Copyright 2006–2008, Texas Instruments Incorporated
Product Folder Link(s): TLV320AIC31
相關PDF資料
PDF描述
TLV320AIC3253IRGER SPECIALTY CONSUMER CIRCUIT, PQCC24
TLV320AIC3253IRGET SPECIALTY CONSUMER CIRCUIT, PQCC24
TLV320AIC3253IYZKR SPECIALTY CONSUMER CIRCUIT, BGA25
TLV320AIC3253IYZKT SPECIALTY CONSUMER CIRCUIT, BGA25
TLV320AIC32IRHBG4 SPECIALTY CONSUMER CIRCUIT, PQCC32
相關代理商/技術參數
參數描述
TLV320AIC31IRHBT 制造商:Texas Instruments 功能描述:IC CODEC STEREO AUDIO 32-VQFN
TLV320AIC31IRHBTG4 功能描述:接口—CODEC Lo-Pwr Ster Codec for Port Aud/Teleph RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel
TLV320AIC32 制造商:BB 制造商全稱:BB 功能描述:LOW POWER STEREO AUDIO CODEC FOR PORTABLE AUDIO/TELEPHONY
TLV320AIC32_07 制造商:BB 制造商全稱:BB 功能描述:LOW POWER STEREO AUDIO CODEC FOR PORTABLE AUDIO/TELEPHONY
TLV320AIC3204 制造商:TI 制造商全稱:Texas Instruments 功能描述:Ultra Low Power Stereo Audio Codec
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*