參數資料
型號： THS3092DR
廠商： Texas Instruments, Inc.
英文描述： HIGH-VOLTAGE, LOW-DISTORTION, CURRENT-FEEDBACK OPERATIONAL AMPLIFIERS
中文描述： 高壓，低失真，電流反饋運算放大器
文件頁數： 23/34頁
文件大?。?/td> 1605K
代理商： THS3092DR
www.ti.com
PowerPAD LAYOUT CONSIDERATIONS
1. PCB with a top side etch pattern as shown in
Figure 67. There should be etch for the leads as
well as etch for the thermal pad.
2. Place 13 holes in the area of the thermal pad.
These holes should be 10 mils in diameter. Keep
them small so that solder wicking through the
holes is not a problem during reflow.
3. Additional vias may be placed anywhere along
the thermal plane outside of the thermal pad
area. This helps dissipate the heat generated by
the THS3092/6 IC. These additional vias may be
larger than the 10-mil diameter vias directly under
the thermal pad. They can be larger because
they are not in the thermal pad area to be
soldered so that wicking is not a problem.
4. Connect all holes to the internal ground plane.
Note that the PowerPAD is electrically isolated
from the silicon and all leads. Connecting the
PowerPAD to any potential voltage such as V
S-
,
is acceptable as there is no electrical connection
to the silicon.
5. When connecting these holes to the ground
plane, do not use the typical web or spoke via
connection methodology. Web connections have
a high thermal resistance connection that is
useful
for
slowing
the
soldering operations. This makes the soldering of
vias that have plane connections easier. In this
application, however, low thermal resistance is
desired for the most efficient heat transfer. There-
fore, the holes under the THS3092/6 PowerPAD
package should make their connection to the
internal ground plane with a complete connection
around
the
entire
plated-through hole.
6. The top-side solder mask should leave the ter-
minals of the package and the thermal pad area
with its 13 holes exposed. The bottom-side solder
mask should cover the 13 holes of the thermal
pad area. This prevents solder from being pulled
away from the thermal pad area during the reflow
process.
7. Apply solder paste to the exposed thermal pad
area and all of the IC terminals.
8. With these preparatory steps in place, the IC is
simply placed in position and run through the
solder
reflow
operation
surface-mount component. This results in a part
that is properly installed.
POWER DISSIPATION AND THERMAL
CONSIDERATIONS
The
THS3092/6
incorporates
shutoff protection. This protection circuitry shuts down
the amplifier if the junction temperature exceeds
approximately 160
°
C. When the junction temperature
reduces to approximately 140
°
C, the amplifier turns
on again. But, for maximum performance and re-
liability, the designer must take care to ensure that
the design does not exeed a junction temperature of
125
°
C. Between 125
°
C and 150
°
C, damage does not
occur, but the performance of the amplifier begins to
degrade and long term reliability suffers. The thermal
characteristics of the device are dictated by the
package
and
the
PC
dissipation for a given package can be calculated
using the following formula.
P
Dmax
T
max
T
A
JA
where:
P
Dmax
is the maximum power dissipation in the amplifier (W).
T
max
is the absolute maximum junction temperature (
°
C).
T
A
is the ambient temperature (
°
C).
θ
JA
=
θ
JC
+
θ
CA
θ
JC
is the thermal coeffiecient from the silicon junctions to
the case (
°
C/W).
θ
CA
is the thermal coeffiecient from the case to ambient
air (
°
C/W).
THS3092
THS3096
SLOS428A–DECEMBER 2003–REVISED FEBRUARY 2004
automatic
thermal
board.
Maximum
power
heat
transfer
during
For systems where heat dissipation is more critical,
the THS3092 is offered in an 8-pin SOIC (DDA) with
PowerPAD package, and the THS3096 is offered in a
14-pin TSSOP (PWP) with PowerPAD package for
even better thermal performance. The thermal coef-
ficient for the PowerPAD packages are substantially
improved over the traditional SOIC. Maximum power
dissipation levels are depicted in the graph for the
available packages. The data for the PowerPAD
packages assume a board layout that follows the
PowerPAD layout guidelines referenced above and
detailed in the PowerPAD application note (literature
number SLMA002). The following graph also illus-
trates the effect of not soldering the PowerPAD to a
PCB. The thermal impedance increases substantially
which may cause serious heat and performance
issues. Be sure to always solder the PowerPAD to
the PCB for optimum performance.
circumference
of
the
as
any
standard
23
相關PDF資料
PDF描述
THS3096PWPR HIGH-VOLTAGE, LOW-DISTORTION, CURRENT-FEEDBACK OPERATIONAL AMPLIFIERS
THS4001D 270-MHz HIGH-SPEED AMPLIFIER
THS4001EVM 270-MHz HIGH-SPEED AMPLIFIER
THS4051D 70-MHz HIGH-SPEED AMPLIFIERS
THS4051JG 70-MHz HIGH-SPEED AMPLIFIERS
相關代理商/技術參數
參數描述
THS3092DRG4 功能描述:高速運算放大器 Dual Hig-Vltg Low Distortion RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
THS3092EVM 功能描述:放大器 IC 開發工具 THS3092 Eval Mod RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V
THS3095 制造商:TI 制造商全稱:Texas Instruments 功能描述:HIGH-VOLTAGE, LOW-DISTORTION, CURRENT-FEEDBACK OPERATIONAL AMPLIFIERS
THS3095D 功能描述:高速運算放大器 Single Lo-Distort Current Feedback RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
THS3095DDA 功能描述:高速運算放大器 Single Lo-Distort Current Feedback RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*