- 您現在的位置：買賣IC網 > PDF目錄98217 > THS1031IPWR (TEXAS INSTRUMENTS INC) 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 PDF資料下載
參數資料
| 型號： | THS1031IPWR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | ADC |
| 英文描述： | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| 封裝： | GREEN, PLASTIC, TSSOP-28 |
| 文件頁數： | 19/41頁 |
| 文件大?。?/td> | 728K |
| 代理商： | THS1031IPWR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
THS1031
3-V TO 5.5-V, 10-BIT, 30 MSPS
CMOS ANALOG-TO-DIGITAL CONVERTER
SLAS242E – NOVEMBER 1999 – REVISED MARCH 2002
26
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
power management
In power-sensitive applications (such as battery-powered systems) where the THS1031 ADC is not required
to convert continuously, power can be saved between conversion intervals by placing the THS1031 into
power-down mode. This is achieved by setting bit 3 (PWDN) of the control register to 1. In power-down mode,
the device typically consumes less than 1 mW of power in either top/bottom or center-span modes. Power-down
mode is exited by resetting control register bit 3 to 0. On power up, the THS1031 typically requires 5 ms of
wake-up time before valid conversion results are available.
In systems where the ADC must run continuously, but where the clamp is not required, setting control register
bit 6 (CLDIS to 1), which disables only the clamp circuits, can save power.
Disabling the ORG in applications where the ORG output is not required can also reduce power dissipation by
1 mA analog IDD. This is achieved by connecting the REFSENSE pin to AVDD.
output format and digital I/O
While the OE pin is held low, ADC conversion results are output at pins I/O0 (LSB) to I/O9 (MSB). The ADC input
over-range indicator is output at pin OVR. OVR is also disabled when OE is held high.
The default ADC output data format is unsigned binary (output codes 0 to 1023). The output format can be
switched to 2s complement (output codes –512 to 511) by setting control register bit 5 (TWOC) to 1.
writing to the internal registers through the digital I/O bus
Pulling pin OE high disables the I/O and OVR pin output drivers, placing the driver outputs in a high impedance
state. This allows control register data to be loaded into the THS1031 by presenting it on the I/O0 to I/O9 pins
and pulsing the WR pin high to latch the data into the chosen control or DAC register.
Figure 31 shows an example register write cycle where the clamp DAC code is set to 10F (hex) by writing to
clamp registers 1 and 2 (see the register map in Table 3). Pins I/O0 to I/O7 are driven to the clamp DAC code
lower byte (0F hex) and pins I/08 and I/O9 are both driven to 0 to select clamp register 1 as the data destination.
The clamp low-byte data is then loaded into this register by pulsing WR high. The top 2 bits of the DAC word
are then loaded by driving 01(hex) on pins I/O0 to I/O7 and by driving pin I/O8 to 1 and pin I/O9 to 0 to select
clamp register 2 as the data destination. WR is pulsed a second time to latch this second control word into clamp
register 2. Interface timing parameters are given in Figures 1 and 2.
OE
WR
I/O (0–9)
Output
Input 00F
Input 101
Output
Load 0F Into
REGISTER 0
Load 01 Into
REGISTER 1
Figure 31. Example Register Write Cycle to Clamp DAC Register
相關PDF資料 |
PDF描述 |
|---|---|
| THS1031CPWRG4 | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1031IDW | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1031CPW | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1031CDW | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
| THS1031IDWR | 1-CH 10-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS1031IPWRG4 | 功能描述:模數轉換器 - ADC 10-Bit 30 MSPS 1-Ch RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| THS1031SOIC | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.7 V . 5.5 V, 10-BIT, 30 MSPS CMOS ANALOG-TO-DIGITAL CONVERTER |
| THS1031TSSOP | 制造商:TI 制造商全稱:Texas Instruments 功能描述:2.7 V . 5.5 V, 10-BIT, 30 MSPS CMOS ANALOG-TO-DIGITAL CONVERTER |
| THS10330RJ | 功能描述:線繞電阻器 - 底架安裝 THS10 330R 5% RoHS:否 制造商:Vishay/Dale 電阻:7 Ohms 容差:1 % 功率額定值:100 W 溫度系數:50 PPM / C 系列:RH 工作溫度范圍:- 55 C to + 250 C 尺寸:46.02 mm Dia. x 46.02 mm W x 88.9 mm L x 44.45 mm H 封裝:Bulk 產品:Power Resistors Wirewound Aluminum Housed |
| THS10-38R-D | 制造商:Thomas & Betts 功能描述:CATAMOUNT CABLE TIES |
發布緊急采購，3分鐘左右您將得到回復。