- 您現在的位置：買賣IC網 > PDF目錄98211 > TEA5766UK (ST-ERICSSON) FM, AUDIO SINGLE CHIP RECEIVER, PBGA25 PDF資料下載
參數資料
| 型號： | TEA5766UK |
| 廠商： | ST-ERICSSON |
| 元件分類： | 接收器 |
| 英文描述： | FM, AUDIO SINGLE CHIP RECEIVER, PBGA25 |
| 封裝： | 3.30 X 3.25 MM, 0.60 MM HEIGHT, WLCSP-25 |
| 文件頁數： | 52/60頁 |
| 文件大小： | 298K |
| 代理商： | TEA5766UK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
TEA5766UK_1
NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 01 — 22 March 2007
55 of 59
NXP Semiconductors
TEA5766UK
Stereo FM radio + RDS
16.3.3 Rework
In general, rework is not recommended. By rework we mean the process of removing the
chip from the substrate and replacing it with a new chip. If a chip is removed from the
substrate, most solder balls of the chip will be damaged. In that case it is recommended
not to re-use the chip again.
Device removal can be done when the substrate is heated until it is certain that all solder
joints are molten. The chip can then be carefully removed from the substrate without
damaging the tracks and solder lands on the substrate. Removing the device must be
done using plastic tweezers, because metal tweezers can damage the silicon. The
surface of the substrate should be carefully cleaned and all solder and ux residues
and/or underll removed. When a new chip is placed on the substrate, use the ux
process instead of solder on the solder lands. Apply ux on the bumps at the chip side as
well as on the solder pads on the substrate. Place and align the new chip while viewing
with a microscope. To reow the solder, use the solder prole shown in
Application Note
AN10365 “Surface mount reow soldering description”.
16.3.4 Cleaning
Cleaning can be done after reow soldering.
17. References
[1]
The I2C-bus specication — version 2.1, January 2000.
[2]
BS EN 62106 — Specication of the radio data system (RDS) for VHF/FM sound
broadcasting in the frequency range from 87.5 to 108 MHz, 2001.
[3]
Data sheet TEF6892H — Car radio integrated signal processor, 2003 Oct 21.
[4]
JESD22-C101C — JEDEC standard for charged-device model ESD test method.
[5]
Data sheet SAA6588 — RDS/RBDS pre-processor, 2002 Jan 14.
[6]
EN 55020 — Sound and television broadcast receivers and associated
equipment-Immunity characteristics- Limits and methods of measurement, May
2002.
[7]
RDS: The Radio Data System — Dietmar Kopitz and Bev Marks.
相關PDF資料 |
PDF描述 |
|---|---|
| TEA5777HL/N2,118 | AM/FM, AUDIO SINGLE CHIP RECEIVER, PQFP32 |
| TEA5777HN/N2,518 | AM/FM, AUDIO SINGLE CHIP RECEIVER, PQCC48 |
| TEA6300PN | 2 CHANNEL(S), SOUND FADER CONTROL CIRCUIT, PDIP28 |
| TEA6300TD-T | 2 CHANNEL(S), SOUND FADER CONTROL CIRCUIT, PDSO28 |
| TEA6300TD | 2 CHANNEL(S), SOUND FADER CONTROL CIRCUIT, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TEA5766UK/N1,023 | 功能描述:調節器/解調器 FM RADIO + RDS RoHS:否 制造商:Texas Instruments 封裝 / 箱體:PVQFN-N24 封裝:Reel |
| TEA5766UK/N1,118 | 功能描述:調節器/解調器 FM RADIO + RDS RoHS:否 制造商:Texas Instruments 封裝 / 箱體:PVQFN-N24 封裝:Reel |
| TEA5766UK/N1/S21,0 | 功能描述:調諧器 FM RADIO + RDS RoHS:否 制造商:NXP Semiconductors 功能: 噪聲系數: 工作電源電壓: 最小工作溫度: 最大工作溫度: |
| TEA5766UK/N1/S21,1 | 功能描述:調諧器 FM RADIO + RDS RoHS:否 制造商:NXP Semiconductors 功能: 噪聲系數: 工作電源電壓: 最小工作溫度: 最大工作溫度: |
| TEA5766UK/N1-G | 功能描述:調諧器 FM RADIO + RDS RoHS:否 制造商:NXP Semiconductors 功能: 噪聲系數: 工作電源電壓: 最小工作溫度: 最大工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。