- 您現在的位置：買賣IC網 > PDF目錄384966 > TDIS (Xilinx, Inc.) XC1800 Series of In-System Programmable Configuration PROMs PDF資料下載
參數資料
| 型號： | TDIS |
| 廠商： | Xilinx, Inc. |
| 英文描述： | XC1800 Series of In-System Programmable Configuration PROMs |
| 中文描述： | XC1800系列在系統可編程配置PROM的 |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 117K |
| 代理商： | TDIS |
R
XC1800 Series of In-System Programmable Configuration PROMs
6
September 17, 1999 (Version 1.3)
IEEE 1149.1 Boundary-Scan (JTAG)
The XC1800 family is fully compliant with the IEEE Std.
1149.1 Boundary-Scan, also known as JTAG. A Test
Access Port (TAP) and registers are provided to support all
required boundary scan instructions, as well as many of the
optional instructions specified by IEEE Std. 1149.1. In addi-
tion, the JTAG interface is used to implement in-system
programming (ISP) to facilitate configuration, erasure, and
verification operations on the XC1800 device.
Table 3
lists the required and optional boundary-scan
instructions supported in the XC1800. Refer to the IEEE
Std. 1149.1 specification for a complete description of
boundary-scan architecture and the required and optional
instructions.
Table 3: Boundary Scan Instructions
Instruction Register
The Instruction Register (IR) for the XC1800 is 8-bits wide
and is connected between TDI and TDO during an instruc-
tion scan sequence. In preparation for an instruction scan
sequence, the instruction register is parallel loaded with a
fixed instruction capture pattern. This pattern is shifted out
onto TDO (LSB first), while an instruction is shifted into the
instruction register from TDI. The detailed composition of
the instruction capture pattern is illustrated in
Figure 3
.
The ISP Status field, IR(4), contains logic 1 if the device is
currently in ISP mode; otherwise, it will contain 0. The
Security field, IR(3), will contain logic 1 if the device has
been programmed with the security option turned on; other-
wise, it will contain 0.
Figure 3: Instruction Register values loaded into IR
as part of an instruction scan sequence
Boundary Scan Register
The boundary-scan register is used to control and observe
the state of the device pins during the EXTEST, SAMPLE/
PRELOAD, and CLAMP instructions. Each output pin on
the XC1800 has two register stages that contribute to the
boundary-scan register, while each input pin only has one
register stage.
For each output pin, the register stage nearest to TDI con-
trols and observes the output state, and the second stage
closest to TDO controls and observes the 3-state enable
state of the pin.
For each input pin, the register stage controls and observes
the input state of the pin.
Identification Registers
The IDCODE is a fixed, vendor-assigned value that is used
to electrically identify the manufacturer and type of the
device being addressed. The IDCODE register is 32-bits
wide. The IDCODE register can be shifted out for examina-
tion by using the IDCODE instruction.
The IDCODE register has the following binary format:
vvvv:ffff:ffff:aaaa:aaaa:cccc:cccc:ccc1
where
v= the die version number
f=the family code (50h for XC1800 family)
a=the ISP PROM product ID (06h for the XC1804)
c=the company code (49h for Xilinx)
Note: The LSB of the IDCODE register is always read as
logic 1 as defined by IEEE Std. 1149.1
Table 4: IDCODES Assigned to XC1800 devices
Table 4
lists the IDCODE register values for the XC1800
devices.
Boundary-
Scan
Command
Required Instructions
BYPASS
SAMPLE/
PRELOAD
Binary Code
(7:0)
Description
11111111
00000001
Enables BYPASS
Enables boundary-scan
SAMPLE/PRELOAD
operation
Enables boundary-scan
EXTEXT operation
EXTEST
00000000
Optional Instructions
CLAMP
11111010
Enables boundary-scan
CLAMP operation
3-states all outputs
simultaneously
HIGHZ
11111100
IDCODE
11111110
Enables shifting out 32-
bit IDCODE
Enables shifting out 32-
bit USERCODE
USERCODE
11111101
XC1800 Specific Instructions
CONFIG
11101110
Initiates FPGA
configuration by pulsing
CF pin low
IR(7:5)
IR(4)
ISP
StatusSecurity
IR(3)
IR(2)
IR(1:0)
TDI->
0 0 0
0
0 1
->TDO
Note: IR(1:0) = 01 is specified by IEEE Std. 1149.1
ISP-PROM
XC1801
XC1804
IDCODE
05004093h
05006093h
相關PDF資料 |
PDF描述 |
|---|---|
| TDOV | XC1800 Series of In-System Programmable Configuration PROMs |
| TDOXZ | XC1800 Series of In-System Programmable Configuration PROMs |
| TDOZX | XC1800 Series of In-System Programmable Configuration PROMs |
| TDM150 | Twin Diode Module |
| TDM15002 | Twin Diode Module |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDJ-100-16A | 制造商:TALEMA 制造商全稱:TALEMA 功能描述:General Purpose Transformers |
| TDJ-100-16B | 制造商:TALEMA 制造商全稱:TALEMA 功能描述:General Purpose Transformers |
| TDJ106K50CB | 制造商:SHARMA 制造商全稱:Sharma Electro Components,Inc 功能描述:Sharma Tantalum Capacitors |
| TDJ-120-AKA-030 | 制造商:American Technical Ceramics Corp 功能描述:ON-DELAY/OFF-DELAY RELAY OUTPUT |
| TDJ13312 | 制造商:TE Connectivity 功能描述: 制造商:TE Connectivity / Schrack Brand 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。