- 您現在的位置：買賣IC網 > PDF目錄98205 > TDA9897HL/V3 (NXP SEMICONDUCTORS) SPECIALTY CONSUMER CIRCUIT, PQFP48 PDF資料下載
參數資料
| 型號： | TDA9897HL/V3 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT313-2, LQFP-48 |
| 文件頁數： | 103/103頁 |
| 文件大?。?/td> | 529K |
| 代理商： | TDA9897HL/V3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁當前第103頁
TDA9897_TDA9898_4
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 25 May 2009
99 of 103
NXP Semiconductors
TDA9897; TDA9898
Multistandard hybrid IF processing
For further information on temperature proles, refer to Application Note
AN10365
“Surface mount reow soldering description”.
17. Soldering of through-hole mount packages
17.1 Introduction to soldering through-hole mount packages
This text gives a very brief insight into wave, dip and manual soldering.
Wave soldering is the preferred method for mounting of through-hole mount IC packages
on a printed-circuit board.
17.2 Soldering by dipping or by solder wave
Driven by legislation and environmental forces the worldwide use of lead-free solder
pastes is increasing. Typical dwell time of the leads in the wave ranges from
3 seconds to 4 seconds at 250
°C or 265 °C, depending on solder material applied, SnPb
or Pb-free respectively.
The total contact time of successive solder waves must not exceed 5 seconds.
The device may be mounted up to the seating plane, but the temperature of the plastic
body must not exceed the specied maximum storage temperature (Tstg(max)). If the
printed-circuit board has been pre-heated, forced cooling may be necessary immediately
after soldering to keep the temperature within the permissible limit.
17.3 Manual soldering
Apply the soldering iron (24 V or less) to the lead(s) of the package, either below the
seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is
less than 300
°C it may remain in contact for up to 10 seconds. If the bit temperature is
between 300
°C and 400 °C, contact may be up to 5 seconds.
MSL: Moisture Sensitivity Level
Fig 54. Temperature proles for large and small components
001aac844
temperature
time
minimum peak temperature
= minimum soldering temperature
maximum peak temperature
= MSL limit, damage level
peak
temperature
相關PDF資料 |
PDF描述 |
|---|---|
| TDA9897HN/V3 | SPECIALTY CONSUMER CIRCUIT, PQCC48 |
| TDA9898HN/V2 | SPECIALTY CONSUMER CIRCUIT, PQCC48 |
| TDA9898HL/V2/S1 | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| TDA9897HL/V2/S1 | SPECIALTY CONSUMER CIRCUIT, PQFP48 |
| TDA9897HN/V2 | SPECIALTY CONSUMER CIRCUIT, PQCC48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA9897HN | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multistandard hybrid IF processing |
| TDA9897HN/V3 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multistandard hybrid IF processing |
| TDA9897S1 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multistandard hybrid IF processing |
| TDA9897V2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multistandard hybrid IF processing |
| TDA9898 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multistandard hybrid IF processing |
發布緊急采購，3分鐘左右您將得到回復。