參數資料
型號： TDA9330
廠商： NXP Semiconductors N.V.
英文描述： I2C-bus controlled TV display processors
中文描述： 的I2C控制的電視顯示處理器總線
文件頁數： 28/56頁
文件大小： 228K
代理商： TDA9330
2000 May 08
28
Philips Semiconductors
Preliminary specification
I
2
C-bus controlled TV display processors
TDA933xH series
Notes
1.
The normal operation of the IC is guaranteed for a supply voltage between 7.2 and 8.8 V. When the supply voltage
drops below the POR level, status bit POR is set and the horizontal output is switched off. When the supply voltage
is between 7.2 V and the POR level, the horizontal frequency is kept in the specified holding range.
For the low power start-up mode, a voltage of 5 V has to be supplied to pin 22. The current that is required for this
function is about 3.0 mA. After the start-up voltage is applied, the signal at the horizontal drive output will have
nominal t
off
, while t
on
grows gradually from zero to about 30% of the nominal value, resulting in a line frequency of
approximately 50 kHz (2fH) or 25 kHz (1fH). The start-up mode is continued as soon as the main supply voltage is
switched on and the I
2
C-bus data has been received. After status bit POR has been read out, bits STB must be set
to 1 within 24 ms, to continue slow start. If bits STB are not sent within 24 ms, the horizontal output will be
automatically switched off via slow stop. It is also possible to first set bits STB to 1, before reading bit POR. Start-up
of the horizontal output will then continue 24 ms after bit POR is read. When the main supply is present, the 5 V
supply on pin 22 can be removed. If low power start-up is not used, pin 22 should be connected to ground. More
information can be found in the application report.
The RGB to YUV matrix on the RGB-1 input is the inverse of the YUV to RGB matrix for PAL. For a one-on-one
transfer of all three channels from the RGB-1 input to the RGB output, the PAL colour difference matrix should be
selected (MAT = 0, MUS = 0).
The colorimetry that is used for high definition ATSC signals is described in document ANSI/SMPTE 274M-1995.
The formula to compute the luminance signal from the RGB primary components differs from the formula that is used
for the PAL system. The consequence is that a different matrix is needed to calculate the internal G
Y signal from
the R
Y and B
Y signals, see the formulas below:
2.
3.
4.
The G
Y signal can be derived from the formula for Y:
G
Y
–
0.2973
–
R
Y
–
(
)
0.1010 B
–
=
I
2
C-bus control inputs/outputs; pins 10 and 11
V
IL
V
IH
I
IL
I
IH
V
OL
DAC
OUTPUT
;
PIN
25; note 47
LOW-level input voltage
HIGH-level input voltage
LOW-level input current
HIGH-level input current
LOW-level output voltage
3.5
0
0
1.5
5.5
0.6
V
V
μ
A
μ
A
V
V
IL
= 0 V
V
IH
= 5.5 V
SDA; I
OL
= 6 mA
V
o(min)
V
o(max)
Z
o
I
o
minimum output voltage
maximum output voltage
output impedance
output current
0.15
3.7
0.3
0.3
4.0
0.4
4.3
10
2
V
note 47
k
mA
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Y
0.2126R
0.7152G
0.0722B
+
+
=
R
Y
–
0.7874R
0.7152G
–
0.0722B
1.575 maximum amplitude
(
)
–
=
B
Y
–
0.2126R
–
0.7152G
–
0.9278B
1.856 maximum amplitude
(
)
+
=
Y
–
)
相關PDF資料
PDF描述
TDA9330H I2C-bus controlled TV display processors
TDA9331H I2C-bus controlled TV display processors
TDA9332 I2C-bus controlled TV display processors
TDA9332H I2C-bus controlled TV display processors
TDA9850 I2C-bus controlled BTSC stereo/SAP decoder
相關代理商/技術參數
參數描述
TDA9330H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:I2C-bus controlled TV display processors
TDA9331H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:I2C-bus controlled TV display processors
TDA9332 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:I2C-bus controlled TV display processors
TDA9332H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:I2C-bus controlled TV display processors
TDA9380 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TDA938O超級芯片將微處理器(CPU)與TV信號處理器集成在一起
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*