- 您現在的位置：買賣IC網 > PDF目錄383940 > TDA5345HT (NXP SEMICONDUCTORS) 5 V spindle & VCM driver combo PDF資料下載
參數資料
| 型號： | TDA5345HT |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 運動控制電子 |
| 英文描述： | 5 V spindle & VCM driver combo |
| 中文描述： | DISK DRIVE MOTOR CONTROLLER, 2 A, PQFP64 |
| 封裝： | LOW PROFILE, PLASTIC, TQFP-64 |
| 文件頁數： | 14/44頁 |
| 文件大?。?/td> | 213K |
| 代理商： | TDA5345HT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
1999 June 10
14
Philips Semiconductors
Preliminary specification
5 V spindle & VCM driver combo
TDA5345HT
Commutation control
D
ELAYS
The spindle block contains both the low-side and high-side drivers configured as a H bridge for a three phase DC
brushless, sensorless motor. In each of the six possible states, two outputs are active, one sourcing current and one
sinking current. The third output presents a high impedance to the motor which enables measurement of the BEMF in
the corresponding motor coil. The back-EMF comparator output (available on pin SpinDigOut) is processed by the
commutation logic circuit to calculate the correct time for the next commutation, which will change the output state.
The commutation block measures then the time between 2 consecutive zero-crossings and determines the actual
commutation time and the next motor coils state. All the following situations must be taken into account:
=> Start up, No start, Backwards spin, Run and Manual commutation.
The commutation logic keeps the motor spinning by commutating the motor each time a zero-crossing is detected. The
delay between the zero-crossing and the actual output driver change is either internally calculated or programmable via
the serial port (useful at start-up: no delay has been measured!).
The internal commutation clock can be monitored on pin SpinDigOut (44). The falling edges are the relevant
informations: they are caused by the zero-crossings. If preferred, SpinDigOut can be set to become the back-EMF
comparator output, to check if the spindle is already spinning at power up for instance. If the spindle outputs are floating,
don’t forget to bias them, using the “BiasCT” bit, before considering the BemfCompOut value.
Fig.6 and Fig.7 show typical motor commutation timing diagrams.
SpinMotA
SpinMotB
SpinMotC
Commutation
Clock
BemfCompOut
L
L
F
H
H
F
H
F
L
L
F
H
F
H
H
F
L
L
Fig.7 Input commutations to output drivers
Zero-crossing
State Code
0
1
2
3
4
5
相關PDF資料 |
PDF描述 |
|---|---|
| TDA5360 | Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads |
| TDA5360UH | Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads |
| TDA5360UK | Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads |
| TDA5630 | 9 V VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners |
| TDA5630BT | 9 V VHF and UHF mixer/oscillator for TV and VCR cable tuners |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA5360 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads |
| TDA5360UH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads |
| TDA5360UK | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pre-Amplifier for Hard Disk Drive with MR-Read / Inductive Write Heads |
| TDA5510-2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Video IF IC with VTR Connection |
| TDA5630 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:9 V VHF, hyperband and UHF mixer/oscillator for TV and VCR 3-band tuners |
發布緊急采購，3分鐘左右您將得到回復。