- 您現在的位置：買賣IC網 > PDF目錄384965 > TDA4916GG (SIEMENS A G) SMPS-IC with MOSFET Driver Output PDF資料下載
參數資料
| 型號： | TDA4916GG |
| 廠商： | SIEMENS A G |
| 元件分類： | 穩壓器 |
| 英文描述： | SMPS-IC with MOSFET Driver Output |
| 中文描述： | SWITCHING CONTROLLER, PDSO24 |
| 文件頁數： | 6/27頁 |
| 文件大小： | 918K |
| 代理商： | TDA4916GG |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
TDA 4916 GG
Semiconductor Group
6
05.96
Comparator K1 (duty factor setting for voltage mode control)
The two plus inputs of the comparator are so connected that the lower plus level is
always compared with the minus input level. As soon as the voltage of the rising edge of
the sawtooth (minus input) exceeds the lower of the two plus input levels, the output is
inhibited via the turn-OFF Flip-Flop, that is to say the High time of the output can be
continuously varied. Since the frequency remains constant, this corresponds to a duty
factor change.
Comparator K2
The comparator has a switching threshold at 1.5 V. Its output sets the fault Flip-Flop
when the voltage on capacitor
C
a
lies below 1.5 V. However, the fault Flip-Flop accepts
the setting pulse only if no reset pulse (fault) is applied. This prevents resetting of the
output as long as a fault signal is present.
Comparators K3 (overvoltage), K4 (undervoltage),
V
S
Undervoltage,
V
REF
Overcurrent
These are fault detectors which cause the output to be inhibited immediately by the fault
Flip-Flop when faults occur. When faults are no longer present, the duty factor is
reestablished via the soft start
C
SS
. In the event of undervoltage, a current is injected at
the input of K4 with the aid of which an adjustable hysteresis or latching is made
possible. The value of the hysteresis is determined by the internal resistance of the
external drive source and the current injected internally at the input of K4. In the event
of undervoltage at K4, the injected current flows into the device.
Comparator K5 (duty factor setting for current mode control)
K5 is used to sense the source current at the switching transistor. The plus input of the
comparator is fed out. Enabling of output Q SIP after cessation of the fault is effected
with an H signal at the turn-OFF Flip-Flop output.
Comparator K6 (overcurrent turn-OFF)
The turn-OFF Flip-Flop is reset when overcurrent is detected by K6. In combination with
the pulse-omission facility, individual pulses can then be omitted. This then results in a
limited rise in the output current with a rising overload at the output.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA4919A | SMPS - IC with SIPMOS Driver Output |
| TDA4918A | AB 23C 5#12, 18#16 SKT PLUG |
| TDA4918G | SMPS - IC with SIPMOS Driver Output |
| TDA4919G | SMPS - IC with SIPMOS Driver Output |
| TDA4935 | Stereo/Bridge AF Amplifier 2 x 15W/30W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA4916GGHUMA1 | 制造商:Infineon Technologies AG 功能描述:Switch Mode Power Supply 24-Pin DSO 制造商:Infineon Technologies AG 功能描述:IC SMPS W/ MOSFET OUTPUT PDSO-24 |
| TDA4916GGNT | 制造商:Infineon Technologies AG 功能描述:Switch Mode Power Supply 24-Pin DSO |
| TDA4918 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:開關電源控制IC |
| TDA4918A | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:SMPS - IC with SIPMOS Driver Output |
| TDA4918G | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:SMPS - IC with SIPMOS Driver Output |
發布緊急采購，3分鐘左右您將得到回復。