- 您現在的位置：買賣IC網 > PDF目錄382579 > TC94A29FB (Toshiba Corporation) TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic PDF資料下載
參數資料
| 型號： | TC94A29FB |
| 廠商： | Toshiba Corporation |
| 英文描述： | TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic |
| 中文描述： | 東芝的CMOS數字集成電路硅單片 |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 282K |
| 代理商： | TC94A29FB |
TC94A29FAG/FB
2003-04-01
6
Pin
No.
Symbol
Pin Name
Function and Operation
Remarks
52
53
54
55
P2-0/COM1
P2-1/COM2
P2-2/COM3
P2-3/COM4
I/O port 2
/LCD common output
56
TEST
/P3-0/S1
Test input
/I/O port 3-0
/LCD segment output
57
58
59
P3-1/S2
P3-2/S3
P3-3/S4
I/O port 3
/LCD segment output
60
61
62
63
P4-0/S5
P4-1/S6
P4-2/S7
P4-3/S8
I/O port 4
/LCD segment output
24-bit CMOS I/O port and 3-bit N-channel
open-drain I/O port.
Input/output can be specified for each bit. When
the P6-0 to P6-3 pins are used as I/O port input,
each pin can be pulled up or down by program.
When the P5-1 (BRK3) to P7-2 (BRK16) pins
are used as I/O port input and backup release
for clock stop mode or wait mode is enabled for
those pins (enabled/disabled in port units), a
change in any of the pins can release the
backup state. The P7-0 to P7-2 pins constitute
an N-channel open-drain I/O port, to which a
voltage of up to 5.5 V can be applied.
I/O ports 2 to 6 can be set to LCD driver output
pins by program. The COM1 to COM4 pins
drive common signals to the LCD panel while
the S1 to S16 pins drive segment signals. The
COM1 to COM4 signals configure a matrix with
the S1 to S16 signals to display up to 64
segments.
When the LCDoff bit is set to 0, the COM1 to
COM4 and S1 to S4 pins are collectively set to
LCD output. For S5 to S16, the program can
specify either I/O port or segment output
individually for each pin.
The LCD can be driven by the 1/4-duty, 1/2-bias
method (frame frequency: 62.5 Hz) or the
1/4-duty, 1/3-bias method (frame frequency: 125
Hz). When the 1/2 bias method is set, three
common output levels (MVDD, 1/2MVDD and
GND) and two segment output levels (MVDD
and GND) appear on the pins. When the 1/3
bias method is set, four common and segment
output levels (MVDD, 1/3MVDD, 2/3MVDD and
GND) appear on the pins.
Upon a system reset or after clock stop mode is
released, a non-select waveform (bias voltage)
is driven and the DISP OFF bit is set to 0, after
which the common signals are driven.
During a system reset (
RESET
low), the
TEST/P3-0/S1 pin is pulled down and accepts
test mode input. This pin should be left open or
applied low level during a reset.
The P5-1 to P6-3 and P1-0 to P1-2 pins can be
set to CD processor-dedicated pins on a per pin
basis. The CD processor functions are as
follows:
(Continued on next page)
MV
DD
MV
DD
Input
instruction
LCD
voltage
MV
DD
MV
DD
Input
instruction
LCD
voltage
R
IN2
MV
SS
Reset signal
MV
DD
MV
DD
Input
instruction
LCD
voltage
相關PDF資料 |
PDF描述 |
|---|---|
| TC94A29FAG | TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic |
| TCD2553AD | CCD IMAGE SENSOR |
| TCD2556D | CCD LINEAR IMAGE SENSOR |
| TCD2556 | CCD LINEAR IMAGE SENSOR |
| TCM129C14DW | COMBINED SINGLE-CHIP PCM CODEC AND FILTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC94A39 | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:CMOS Digital Intergrated Circuit |
| TC94A39FAG | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Single-Chip CD Processor with Built-in Controller (CD-DX) |
| TC94A39FAG/FB | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:CMOS Digital Intergrated Circuit |
| TC94A39FB | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Single-Chip CD Processor with Built-in Controller (CD-DX) |
| TC94A48FG | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Single-chip Audio Digital Signal Processor |
發布緊急采購，3分鐘左右您將得到回復。