- 您現在的位置：買賣IC網 > PDF目錄98166 > TB62209FG STEPPER MOTOR CONTROLLER, 1.8 A, PDSO38 PDF資料下載
參數資料
| 型號： | TB62209FG |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 1.8 A, PDSO38 |
| 封裝： | 0.450 INCH, 0.65 MM PITCH, PLASTIC, HSOP-26/38 |
| 文件頁數： | 25/51頁 |
| 文件大?。?/td> | 501K |
| 代理商： | TB62209FG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
TB62209FG
2005-03-02
31
Power Supply Sequence (Recommended)
Note 1: If the VDD drops to the level of the VDDR or below while the specified voltage is input to the VM pin, the IC is
internally reset.
This is a protective measure against malfunction. Likewise, if the VM drops to the level of the VMR or below
while regulation voltage is input to the VDD, the IC is internally reset as a protective measure against
malfunction.
To avoid malfunction, when turning on VM or VDD, to input the Standby signal at the above timing is
recommended.
It takes time for the output control charge pump circuit to stabilize. Wait up to tONG time after power on
before driving the motors.
Note 2: When the VM value is between 3.3 to 5.5 V, the internal reset is released, thus output may be on. In such a
case, the charge pump cannot drive stably because of insufficient voltage. The Standby state should be
maintained until VM reaches 13 V or more.
Note 3: Since VDD = 0 V and VM = voltage within the rating are applied, output is turned off by internal reset.
At that time, a current of several mA flows due to the Pass between VM and VDD.
When voltage increases on VDD output, make sure that specified voltage is input.
VDD (max)
VDD (min)
VDDR
GND
VDD
VM
VM (min)
VMR
GND
VM
NON-RESET
RESET
Internal reset
H
L
STANDBY
INPUT (Note 1)
Takes up to tONG until operable.
Non-operable area
STANDBY
相關PDF資料 |
PDF描述 |
|---|---|
| TB62214FTG | STEPPER MOTOR CONTROLLER, 2 A, PQCC48 |
| TB62754AFNG | SWITCHING REGULATOR, PDSO20 |
| TB62756FUG | SWITCHING REGULATOR, 1430 kHz SWITCHING FREQ-MAX, PDSO6 |
| TB62757FUG | SWITCHING REGULATOR, 1430 kHz SWITCHING FREQ-MAX, PDSO6 |
| TB6512AFG | STEPPER MOTOR CONTROLLER, 0.12 A, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB62209FG(EL) | 功能描述:馬達/運動/點火控制器和驅動器 Stepping Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB62209FG(O,EL) | 功能描述:馬達/運動/點火控制器和驅動器 Stepping Motor PWM 40V 1.8A RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB62209SN | 制造商:THOMAS & BETTS 功能描述: |
| TB622-100.0M | 制造商:Connor-Winfield 功能描述:OSC TCXO 100MHZ 3.3V SMD |
| TB-6221-01 | 功能描述:界面模塊 SWITCH TERMINATION BRD 62P D-SUB FEMALE RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。