參數資料
型號: TB62209FG
元件分類: 運動控制電子
英文描述: STEPPER MOTOR CONTROLLER, 1.8 A, PDSO38
封裝: 0.450 INCH, 0.65 MM PITCH, PLASTIC, HSOP-26/38
文件頁數: 11/51頁
文件大?。?/td> 501K
代理商: TB62209FG
TB62209FG
2005-03-02
19
Electrical Characteristics 3 (unless otherwise specified, Ta
= 25°C, VDD = 5 V, VM = 24 V)
Characteristics
Symbol
Test
Circuit
Test Condition
Min
Typ.
Max
Unit
Vref input voltage
Vref
DC
VM = 24 V, VDD = 5 V,
STANDBY
= H, RESET = L,
Output on, CLK
= 1 kHz
2.0
VDD
V
Vref input current
Iref
DC
STANDBY
= H, RESET = L,
Output off, VM = 24 V,
VDD = 5 V, Vref = 3.0 V
20
35
50
A
Vref attenuation ratio
Vref (GAIN)
DC
VM = 24 V, VDD = 5 V,
STANDBY
= H, RESET= L,
Output on,
Vref = 2.0 to VDD 1.0 V
1/4.8
1/5.0
1/5.2
TSD temperature
(Note 1)
TjTSD
DC
VDD = 5 V, VM = 24 V
130
170
°C
TSD return temperature difference
(Note 1)
TjTSD
DC
TjTSD = 130 to 170°C
TjTSD
50
TjTSD
35
TjTSD
20
°C
VDD return voltage
VDDR
DC
VM = 24 V, STANDBY = H
2.0
3.0
4.0
V
VM return voltage
VMR
DC
VDD = 5 V, STANDBY = H
2.0
3.5
5.0
V
Over current protected circuit
operation current
(Note 2)
ISD
DC
VDD = 5 V, VM = 24 V
3.0
A
High temperature monitor pin
output current
Iprotect
DC
VDD = 5 V,
TSD
= operating condition
1.0
3.0
5.0
mA
Electrical angle monitor pin output
current
IMO
DC
VDD = 5 V,
electrical angle
= 0°
(IB
= 100%, IA = 0%)
1.0
3.0
5.0
mA
Vprotect (H)
DC
VDD = 5 V,
TSD
= operating condition
5.0
High temperature monitor pin
output voltage
Vprotect (L)
DC
VDD = 5 V,
TSD
= not operating
condition
0.0
V
VMO2 (H)
DC
VDD = 5 V,
electrical angle
= except 0°
(IB
= 100%,
IA
= Except 0% set)
5.0
Electrical angle monitor pin output
voltage
VMO2 (L)
DC
VDD = 5 V,
electrical angle
= 0°
(IB
= 100%, IA = 0%)
0.0
V
Note 1: Thermal shut down (TSD) circuit
When the IC junction temperature reaches the specified value and the TSD circuit is activated, the internal
reset circuit is activated switching the outputs of both motors to off.
When the temperature is set between 130 (min) to 170°C (max), the TSD circuit operates.
When the TSD circuit is activated, the charge pump is halted, and TROTECT pin outputs VDD voltage.
Even if the TSD circuit is activated and
Standby goes H → L → H instantaneously, the IC is not reset until
the IC junction temperature drops 20°C (typ.) below the TSD operating temperature (hysteresis function).
Note 2: Overcurrent protection circuit
When current exceeding the specified value flows to the output, the internal reset circuit is activated, and the
ISD turns off the output.
Until the Standby signal goes Low to High, the overcurrent protection circuit remains activated.
During ISD, IC turns Standby mode and the charge pump halts.
相關PDF資料
PDF描述
TB62214FTG STEPPER MOTOR CONTROLLER, 2 A, PQCC48
TB62754AFNG SWITCHING REGULATOR, PDSO20
TB62756FUG SWITCHING REGULATOR, 1430 kHz SWITCHING FREQ-MAX, PDSO6
TB62757FUG SWITCHING REGULATOR, 1430 kHz SWITCHING FREQ-MAX, PDSO6
TB6512AFG STEPPER MOTOR CONTROLLER, 0.12 A, PDSO24
相關代理商/技術參數
參數描述
TB62209FG(EL) 功能描述:馬達/運動/點火控制器和驅動器 Stepping Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TB62209FG(O,EL) 功能描述:馬達/運動/點火控制器和驅動器 Stepping Motor PWM 40V 1.8A RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TB62209SN 制造商:THOMAS & BETTS 功能描述:
TB622-100.0M 制造商:Connor-Winfield 功能描述:OSC TCXO 100MHZ 3.3V SMD
TB-6221-01 功能描述:界面模塊 SWITCH TERMINATION BRD 62P D-SUB FEMALE RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: