- 您現在的位置：買賣IC網 > PDF目錄98166 > TB62209FG STEPPER MOTOR CONTROLLER, 1.8 A, PDSO38 PDF資料下載
參數資料
| 型號： | TB62209FG |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 1.8 A, PDSO38 |
| 封裝： | 0.450 INCH, 0.65 MM PITCH, PLASTIC, HSOP-26/38 |
| 文件頁數： | 1/51頁 |
| 文件大?。?/td> | 501K |
| 代理商： | TB62209FG |
當前第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
TB62209FG
2005-03-02
1
TOSHIBA BiCD Processor IC
Silicon Monolithic
TB62209FG
Stepping Motor Driver IC Using PWM Chopper Type
The TB62209FG is a stepping motor driver driven by chopper
micro-step pseudo sine wave.
The TB62209FG integrates a decoder for CLK input in micro
steps as a system to facilitate driving a two-phase stepping motor
using micro-step pseudo sine waves. Micro-step pseudo sine
waves are optimal for driving stepping motors with low-torque
ripples and at low oscillation. Thus, the TB62209FG can easily
drive stepping motors with low-torque ripples and at high
efficiency.
Also, TB62209FG consists output steps by DMOS (Power MOS
FET), and that makes possible to control the output power
dissipation much lower than ordinary IC with bipolar transistor
output.
The IC supports Mixed Decay mode for switching the attenuation ratio at chopping. The switching time for the
attenuation ratio can be switched in four stages according to the load.
Features
Bipolar stepping motor can be controlled by a single driver IC
Monolithic BiCD IC
Low ON-resistance of Ron = 0.5 (Tj = 25°C @1.0 A: typ.)
Built-in decoder and 4-bit DA converters for micro steps
Built-in ISD, TSD, VDD &VM power monitor (reset) circuit for protection
Built-in charge pump circuit (two external capacitors)
36-pin power flat package (HSOP36-P-450-0.65)
Output voltage: 40 V max
Output current: 1.8 A/phase max
2-phase, 1-2 (type 2) phase, W1-2 phase, 2W1-2 phase, 4W1-2 phase, or motor lock mode can be selected.
Built-in Mixed Decay mode enables specification of four-stage attenuation ratio.
Chopping frequency can be set by external resistors and capacitors.
High-speed chopping possible at 100 kHz or higher.
Note: When using the IC, pay attention to thermal conditions. These devices are easy damage by high static
voltage. In regards to this, please handle with care.
Weight: 0.79 g (typ.)
相關PDF資料 |
PDF描述 |
|---|---|
| TB62214FTG | STEPPER MOTOR CONTROLLER, 2 A, PQCC48 |
| TB62754AFNG | SWITCHING REGULATOR, PDSO20 |
| TB62756FUG | SWITCHING REGULATOR, 1430 kHz SWITCHING FREQ-MAX, PDSO6 |
| TB62757FUG | SWITCHING REGULATOR, 1430 kHz SWITCHING FREQ-MAX, PDSO6 |
| TB6512AFG | STEPPER MOTOR CONTROLLER, 0.12 A, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB62209FG(EL) | 功能描述:馬達/運動/點火控制器和驅動器 Stepping Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB62209FG(O,EL) | 功能描述:馬達/運動/點火控制器和驅動器 Stepping Motor PWM 40V 1.8A RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB62209SN | 制造商:THOMAS & BETTS 功能描述: |
| TB622-100.0M | 制造商:Connor-Winfield 功能描述:OSC TCXO 100MHZ 3.3V SMD |
| TB-6221-01 | 功能描述:界面模塊 SWITCH TERMINATION BRD 62P D-SUB FEMALE RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。