
Ver3.7
00/01/28  
39
Note
V14
Items/Symbols
Black Expansion Start
Point
 / V
BLEX25
 / V
BLEX35
 / V
BLEX45
Bus conditoins
Uni-Color:127
Color:0
Black
stretch:00/01
     /10/11
RGB Mute:0
R cut off:63
DC rest.:10
Others:Preset
Measurement methods
(1) nput a gray raster with sync to Pin38&39.
(2) Set black stretch to 25IRE.
(3) Decreasing Y amplitude of input from 50IRE, measure a Y
amplitude as the figure below, that is “V
BLEX25
”
(4) Set black stretch to 35IRE/45IRE.
(5) Repeat (3), that is ‘V
BLEX35
”, “V
BLEX45
”. below, that is “V
Y
 90
”
(6) Find gain of the portion that the black stretch has an effect on.
#20
output
Black Expansion AMP
Gain
 / G
BLEX
Black
stretch
=off
25/35/45IRE
#39 input
V
BLEX25
V16
DC Restration Gain
 / V
Dcrest120
 / V
Dcrest90
 / V
Dcrest step
Uni-Color:127
Color:0
Black
stretch:00/01
     /10/11
RGB Mute:0
R cut off:63
DC rest.:10
Others:Preset
Uni-Color:127
Brightness:127
Color:0
RGB Mute:0
R cut off:63
DC rest.:10
Others:Preset
C-Trap:0/1
Uni-Color:127
Color:0
RGB Mute:0
R cut off:63
DC 
Others:Preset
Ysm Mode:0
Uni-Color:127
Color:0
RGB Mute:0
R cut off:63
DC rest.:10
Others:Preset
(1) nput a 100IRE signal with sync into Pin38&39.
(2) Set DC rest. to 10.
(3) Measure a Y amplitude of pin20 output, that is V100.
(4) Set DC rest to 00.
(5) Measure a Y amplitude of pin20 output, that is V120.
(6) Calculate, “V
dcrest120
” =(V120/V100)
×
100
(7) Set DC rest to 11.
(8) Repeat (5)&(6), that is “V
Dcrest90
”.
(9) Calculate, “V
Dcrest step
”=(V
dcrest120 
- V
Dcrest90
)/4
(1)Input a 120IRE ramp signal with sync into Pin38&39.
(2)Measure the amplitude from cut-off level to peak(at which
output signal is clipped), that is "V
WPS
".
V17
WPS Level
 / V
WPS
V18
Chroma Trap Gain
 / G
TRAP
rest.:10
(1)Input a 0.5Vp-p, 3.58MHz signal with sync into Pin43&39.
(2)Measure the 3.58MHz amplitude at PIn20 for Chroma
Trap:1/0, that is V
TRAPON
 / V
TRAPOFF
.
(3)Calculate;"G
TRAP
"=20*log(V
TRAPON
/V
TRAPOFF
)
V19
Half 
Characteristics for Y
 / G
HTY
Tone
(1)Input a 100IRE white signal with sync into Pin38&39.
(2)Measure the output picture amplitude at PIn20 , that is
V
HTYOFF
.
(3)Suppry Pin15 2V.
(4) Measure the output picture amplitude at PIn20 , that is V
HTYON
.
(3)Calculate;"G
HTY
"=20*log(V
HTYON
/V
HTYOFF
)