- 您現在的位置：買賣IC網 > PDF目錄98164 > TAS5704PAPR (TEXAS INSTRUMENTS INC) 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 PDF資料下載
參數資料
| 型號： | TAS5704PAPR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| 封裝： | GREEN, PLASTIC, HTQFP-64 |
| 文件頁數： | 19/38頁 |
| 文件大?。?/td> | 735K |
| 代理商： | TAS5704PAPR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
OUTA
L
filter
C
filter
OUTA
L
filter
C
filter
L
filter
OUTB
C
filter
SLOS563A – MARCH 2008 – REVISED AUGUST 2010
www.ti.com
Figure 29. BTL Filter Configuration
Figure 30. SE Filter Configuration
POWER-SUPPLY DECOUPLING, CS
The TAS5704 is a high-performance CMOS audio amplifier that requires adequate power-supply decoupling to
ensure that the output total harmonic distortion (THD) is as low as possible. Power-supply decoupling also
prevents oscillations for long lead lengths between the amplifier and the speaker. The optimum decoupling is
achieved by using two capacitors of different types that target different types of noise on the power-supply leads.
For higher-frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR)
ceramic capacitor, typically 0.1 mF to 1 mF, placed as close as possible to the device VCC lead works best. For
filtering lower frequency noise signals, a larger aluminum electrolytic capacitor of 220 mF or greater placed near
the audio power amplifier is recommended. The 220-mF capacitor also serves as local storage capacitor for
supplying current during large signal transients on the amplifier outputs. The PVCC terminals provide the power
to the output transistors, so a 220-mF or larger capacitor should be placed on each PVCC terminal. A 10-mF
capacitor on the AVCC terminal is adequate. These capacitors must be properly derated for voltage and
ripple-current rating to ensure reliability.
BOOTSTRAP CAPACITORS
The half H-bridge output stages use only NMOS transistors. Therefore, they require bootstrap capacitors for the
high side of each output to turn on correctly. A 220-nF ceramic capacitor, rated for at least 25 V, must be
connected from each output to its corresponding bootstrap input.
The bootstrap capacitors connected between the BSx pins and their corresponding outputs function as a floating
power supply for the high-side N-channel power MOSFET gate-drive circuitry. During each high-side switching
cycle, the bootstrap capacitors hold the gate-to-source voltage high enough to keep the high-side MOSFETs
turned on.
VCLAMP CAPACITOR
To ensure that the maximum gate-to-source voltage for the NMOS output transistors is not exceeded, one
internal regulator clamps the gate voltage. One 1-mF capacitor must be connected from each VCLAMP (terminal)
to ground and must be rated for at least 16 V. The voltages at the VCLAMP terminal may vary with VCC and may
not be used for powering any other circuitry.
VBYP CAPACITOR SELECTION
The scaled supply reference (BYPASS) nominally provides an AVCC/8 internal bias for the preamplifier stages.
The external capacitor for this reference (CBYP) is a critical component and serves several important functions.
During start-up or recovery from shutdown mode, CBYP determines the rate at which the amplifier starts. The start
up time is proportional to 0.5 s per microfarad in single-ended mode (SE/BTL = DVDD). Thus, the recommended
1-mF capacitor results in a start-up time of approximately 500 ms (SE/BTL = DVDD). The second function is to
reduce noise produced by the power supply caused by coupling with the output drive signal. This noise could
result in degraded power-supply rejection and THD+N.
26
Copyright 2008–2010, Texas Instruments Incorporated
Product Folder Link(s): TAS5704
相關PDF資料 |
PDF描述 |
|---|---|
| TAS5704PAP | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TAS5704PAPG4 | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TAS5705PAPG4 | 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TAS5705PAPRG4 | 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
| TAS5705PAPR | 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TAS5704PAPRG4 | 功能描述:音頻放大器 20W stereo Dig Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TAS5705 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:20-W STEREO DIGITAL AUDIO POWER AMPLIFIER WITH EQ AND DRC |
| TAS5705EVM2 | 功能描述:音頻 IC 開發工具 TAS5705EVM2 Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TAS5705PAP | 功能描述:音頻放大器 20W stereo Dig Audio Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TAS5705PAPG4 | 功能描述:音頻放大器 20W stereo Dig Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。