參數資料
型號： TAS5076PFCR
廠商： TEXAS INSTRUMENTS INC
元件分類： 消費家電
英文描述： SPECIALTY CONSUMER CIRCUIT, PQFP80
封裝： GREEN, PLASTIC, TQFP-80
文件頁數： 21/64頁
文件大小： 873K
代理商： TAS5076PFCR
Architecture Overview
22
SLES090A—November 2003—Revised January 2004
TAS5076
REGISTER
SETTING
FUNCTION
0Ch
01h
TC delay channel 1
0Dh
49h
TC delay channel 2
0Eh
91h
TC delay channel 3
0Fh
39h
TC delay channel 4
10h
21h
TC delay channel 5
11h
69h
TC delay channel 6
These values must be reprogrammed every time RESET is asserted. RESET causes default values to be
loaded.
2.4.6 ABD Delay
A 5-bit value is used to delay the A PWM signals with respect to B PWM signals. The value is the same for
all channels. It can be programmed from 0 to 31 DCLK clock cycles. The default ABD value is 20 DCLK clock
cycles (10100). This value is mask programmable.
This value can be changed at any time through the serial control interface.
The optimum value for ABD delay depends on the final system. This value can be adjusted for better
performance with regard to dynamic range and THD. It is recommended that the following ABD delay value
be set instead of the default value. The ABD delay value in conjunction with the TC delay values delivers the
best performance in the TAS50765182 EVM board.
REGISTER
SETTING
FUNCTION
12h
1Dh
ABD delay
This value must be reprogrammed every time RESET is asserted. RESET causes the default value to be
loaded.
NOTE:
The performance of a PurePath Digital
amplifier system is optimized by setting the PWM
timing based upon the type of back-end device that is used and the layout. These values are
set during initialization using the I2C serial interface.
2.4.7 PWM/H-Bridge and Discrete H-Bridge Driver Interface
The TAS5076 provides six PWM outputs, which are designed to drive switching output stages (back-ends)
in both single-ended (SE) and H-bridge (bridge-tied load) configuration. The back ends can be monolithic
power stages (such as the TAS5110) or six discrete differential power stages using gate drivers (such as the
the TAS55182) and MOSFETs in single-ended or bridged configurations.
The TAS5110 device is optimized for bridge-tied load (BTL) configurations. These devices require a pure
differential PWM signal with a third signal (VALID) to control the MUTE state. In the MUTE state, the TAS5110
OUTA and OUTB are both low.
One Channel
of TAS5076
PWM_AP
PWM_AM
VALID
TAS5110
OUTA
OUTB
AP
AM
RESET
BP
BM
Speaker
PWM_BP
PWM_BM
Figure 212. PWM Outputs and H-Bridge Driven in BTL Configuration
PurePath Digital is a trademark of Texas Instruments.
相關PDF資料
PDF描述
TAS5076PFCRG4 SPECIALTY CONSUMER CIRCUIT, PQFP80
TAS5076PFC SPECIALTY CONSUMER CIRCUIT, PQFP80
TAS5086DBT SPECIALTY CONSUMER CIRCUIT, PDSO38
TAS5086DBTR SPECIALTY CONSUMER CIRCUIT, PDSO38
TAS5086DBTRG4 SPECIALTY CONSUMER CIRCUIT, PDSO38
相關代理商/技術參數
參數描述
TAS5076PFCRG4 功能描述:音頻放大器 6-Ch Digital Audio PWM Processor RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TAS5086 制造商:TI 制造商全稱:Texas Instruments 功能描述:PurePath Digital TM AUDIO SIX-CHANNEL PWM PROCESSOR
TAS5086_06 制造商:TI 制造商全稱:Texas Instruments 功能描述:PurePath Digital TM AUDIO SIX-CHANNEL PWM PROCESSOR
TAS5086-5142V6EVM 功能描述:音頻 IC 開發工具 HI PERF MULTI PWM RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
TAS5086-5186V6EVM 功能描述:音頻 IC 開發工具 HI PERF MULTI PWM RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*