參數資料
型號： TAS5066PAGR
廠商： TEXAS INSTRUMENTS INC
元件分類： 消費家電
英文描述： SPECIALTY CONSUMER CIRCUIT, PQFP64
封裝： GREEN, PLASTIC, TQFP-64
文件頁數： 21/66頁
文件大小： 1023K
代理商： TAS5066PAGR
Architecture Overview
22
SLES089—January 2004
TAS5066
2.4.4 PWM DC-Offset Correction
An 8-bit value can be programmed to each of the six PWM offset correction registers to correct for any offset
present in the output stages. The offset correction is divided into 256 intervals with a total offset correction of
±1.56% of full scale. The default value is zero correction represented by 00 (hex). These values can be
changed at any time through the serial control interface.
2.4.5 Interchannel Delay
An 8-bit value can be programmed to each of the six PWM interchannel delay registers to add a delay per
channel from 0 to 255 clock cycles. The delays correspond to cycles of the high-speed internal clock, DCLK.
Each subsequent channel has a default value that is N DCLKs larger than the preceding channel. The default
interchannel delay for the first channel and the interchannel delay between subsequent channels are mask
programmable. The present values are 0 for the first channel and increments of 53 for each successive
channel.
These values can be updated upon power up through the serial control interface. This delay is generated in
the PWM block with the appropriate control signals generated in the CTL block.
These values can be changed at any time through the serial control interface.
The optimum value for interchannel delay depends on the final system. This value can be adjusted for better
performance with regard to dynamic range and THD. It is recommended that the following TC delay values
be set instead of the default value. These TC delay values deliver the best performance in the test board.
REGISTER
SETTING
FUNCTION
0Ch
01h
TC delay channel 1
0Dh
49h
TC delay channel 2
0Eh
91h
TC delay channel 3
0Fh
39h
TC delay channel 4
10h
21h
TC delay channel 5
11h
69h
TC delay channel 6
These values must be reprogrammed every time RESET is asserted. RESET causes default values to be
loaded.
2.4.6 PWM/H-Bridge and Discrete H-Bridge Driver Interface
The TAS5066 provides six PWM outputs, which are designed to drive switching output stages (back-ends)
in both single-ended (SE) and H-bridge (bridge tied load) configuration. The back-ends may be monolithic
power stages (such as the TAS5110) or six discrete differential power stages using gate drivers (such as the
the TAS55182) and MOSFETs in single-ended or bridged configurations.
The TAS5110 device is optimized for bridge tied load (BTL) configurations. These devices require a pure
differential PWM signal with a third signal (VALID) to control the MUTE state. In the MUTE state, the TAS5110
OUTA and OUTB are both low.
One Channel
of TAS5066
PWM_AP
PWM_AM
VALID
TAS5110
OUTA
OUTB
AP
AM
RESET
BP
BM
Speaker
Figure 212. PWM Outputs and H-Bridge Driven in BTL Configuration
相關PDF資料
PDF描述
TAS5066PAGG4 SPECIALTY CONSUMER CIRCUIT, PQFP64
TAS5076PFCG4 SPECIALTY CONSUMER CIRCUIT, PQFP80
TAS5076PFCR SPECIALTY CONSUMER CIRCUIT, PQFP80
TAS5076PFCRG4 SPECIALTY CONSUMER CIRCUIT, PQFP80
TAS5076PFC SPECIALTY CONSUMER CIRCUIT, PQFP80
相關代理商/技術參數
參數描述
TAS5066PAGRG4 功能描述:音頻 DSP 6Ch Dig Aud PWM Proc RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
TAS5076 制造商:TI 制造商全稱:Texas Instruments 功能描述:SIX-CHANNEL DIGITAL AUDIO PWM PROCESSOR
TAS5076-5182C6EVM 功能描述:音頻 IC 開發工具 TAS5076-5182C6 EVAL MOD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
TAS5076PFC 功能描述:音頻 DSP 6-Ch Digital Audio PWM Processor RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
TAS5076PFCG4 功能描述:音頻 DSP 6-Ch Digital Audio PWM Processor RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*