- 您現在的位置：買賣IC網 > PDF目錄384945 > TA2024 (Electronic Theatre Controls, Inc.) Stereo 10W (4з) Class-T⑩ Digital Audio Amplifier using Digital Power Processing⑩ Technology PDF資料下載
參數資料
| 型號： | TA2024 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 元件分類： | 運動控制電子 |
| 英文描述： | Stereo 10W (4з) Class-T⑩ Digital Audio Amplifier using Digital Power Processing⑩ Technology |
| 中文描述： | 10W的立體聲（4з）類- T的數字音頻放大器⑩使用數字電源技術處理⑩ |
| 文件頁數： | 9/14頁 |
| 文件大?。?/td> | 467K |
| 代理商： | TA2024 |
T E C H N I C A L I N F O R M A T I O N
TA2024 Preliminary, Rev. 1.0
Page 9
Over-current Protection
An over-current fault occurs if more than approximately 7 amps of current flows from any of the
amplifier output pins. This can occur if the speaker wires are shorted together or if one side of the
speaker is shorted to ground. An over-current fault sets an internal latch that can only be cleared if
the MUTE pin is toggled or if the part is powered down. Alternately, if the MUTE pin is connected to
the FAULT pin, the HIGH output of the FAULT pin will toggle the MUTE pin and automatically reset
the fault condition.
Overload
The OVERLOADB pin is a 5V logic output. When low, it indicates that the level of the input signal
has overloaded the amplifier resulting in increased distortion at the output. The OVERLOADB signal
can be used to control a distortion indicator light or LED through a simple buffer circuit, as the
OVERLOADB cannot drive an LED directly.
Sleep Pin
The SLEEP pin is a 5V logic input that when pulled high (>3.5V) puts the part into a low quiescent
current mode. This pin is internally clamped by a zener diode to approximately 6V thus allowing the
pin to be pulled up through a large valued resistor (1meg
recommended) to V
DD
. To disable SLEEP
mode, the sleep pin should be grounded.
Fault Pin
The FAULT pin is a 5V logic output that indicates various fault conditions within the device. These
conditions include: low supply voltage, low charge pump voltage, low 5V regulator voltage, over
current at any output, and junction temperature greater than approximately 155
°
C. All faults except
overcurrent all reset upon removal of the condition. The FAULT output is capable of directly driving
an LED through a series 200
resistor. If the FAULT pin is connected directly to the MUTE input an
automatic reset will occur in the event of an over-current condition.
相關PDF資料 |
PDF描述 |
|---|---|
| TA2050 | GROUND ISOLATOR IC |
| TA2057 | AM/FM IF+FM ST DET (FOR DIGITAL TUNING SYSTEM) |
| TA2099F | AM/FM IF+FM STEREO DETECTOR (FOR DIGITAL TUNING SYSTEM) |
| TA2099N | AM/FM IF+FM STEREO DETECTOR (FOR DIGITAL TUNING SYSTEM) |
| TA2104BFN | 3V AM/FM 1 CHIP TUNER IC (FOR DIGITAL TUNING SYSTEM) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TA202412 | 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Phase Control SCR (1200-1400 Amperes Avg 2400-4000 Volts) |
| TA202414 | 制造商:POWEREX 制造商全稱:Powerex Power Semiconductors 功能描述:Phase Control SCR (1200-1400 Amperes Avg 2400-4000 Volts) |
| TA20241603DH | 功能描述:SCR PHASE CTRL 2400V 1600A RoHS:是 類別:半導體模塊 >> SCR 系列:- 其它有關文件:SCR Module Selection Guide 標準包裝:10 系列:- 結構:串聯 - SCR/二極管 SCR 數目，二極管:1 SCR，1 個二極管 電壓 - 斷路:1600V 電流 - 柵極觸發電流 (Igt)（最大）:150mA 電流 - 導通狀態 (It (AV))（最大）:95A 電流 - 導通狀態 (It (RMS))（最大）:210A 電流 - 非重復電涌，50、60Hz (Itsm):1785A，1870A 電流 - 維持(Ih):250mA 安裝類型:底座安裝 封裝/外殼:ADD-A-PAK（3 + 2） 包裝:散裝 其它名稱:*IRKL92/16AIRKL92/16IRKL92/16-ND |
| TA20241605DN | 制造商:n/a 功能描述:Power Semiconductor |
| TA2024B | 制造商:TRIPATH 制造商全稱:TRIPATH 功能描述:STEREO 15W (4з) CLASS-T⑩ DIGITAL AUDIO AMPLIFIER USING DIGITAL POWER PROCESSING⑩ TECHNOLOGY |
發布緊急采購，3分鐘左右您將得到回復。