- 您現在的位置：買賣IC網 > PDF目錄385896 > TA1204AF (Toshiba Corporation) ャ CORRECTION IC FOR LCD TV PDF資料下載
參數資料
| 型號： | TA1204AF |
| 廠商： | Toshiba Corporation |
| 英文描述： | ャ CORRECTION IC FOR LCD TV |
| 中文描述： | ャ校正集成電路液晶電視 |
| 文件頁數： | 16/25頁 |
| 文件大?。?/td> | 575K |
| 代理商： | TA1204AF |
TA1204AF
2001-02-07 16/25
Note 16:
Signal frequency characteristics, inter-axis deviation
Test condition 5 (CP mode, fixed polarity)
Input :
X In1
Test signal 2 (sweep)
Input test signal 2 to X In1, raise its frequency from 500kHz to 20MHz, and observe the amplitudes
of the frequency components. Measure the frequency for a 3dB fall in output amplitude. Take the
same measurements as for positive polarity by changing SW
7B
from a to b.
Output dynamic range
Test condition 4 (CP mode)
Input :
X In1
Test signal 3
VR23 :
→
Max / Min
Input a signal (0.7V
p-p
) including black and white levels to input A (X In1). Change SW
23
from a to b,
raise and lower the voltage applied to pin 23 by turning VR23 clockwise and anticlockwise, measure
the maximum and minimum black waveform levels for an output pin (pin 21 when X = B, pin 19
when X = G, and pin 14 when X = R), and thus obtain the voltage difference.
Note 17:
Note 18:
Signal output through-rate
Test condition 4 (CP mode)
Input :
X In1
Test signal 5
Input to input A (X In1) a test signal whose 10 to 90% rise / fall times are less than 50ns in a
rectangular waveform that repeats black and white levels. Measure the 10 to 90% rise / fall times in
the waveform of the output pin (pin 21 when X = B, pin 19 when X = G, and pin 14 when X = R), and
convert this to a through-rate.
Note 19:
Signal output S / N
Test condition 5 (CP mode, fixed polarity)
Input : no signal
Noise measurement band DC to 6MHz
Change SW
27
from a to b, and adjust VR27 while looking at the waveform of an output pin (pin 21,
pin 19, pin 14) so that the difference between the
γ
0 and black levels becomes 0. Measure the noise
voltage (measurement band: ~6MHz) of the output pins in this state. Repeat this measurement for
each output pin. Calculate the ratio of the No. 9 typical output amplitude to the measured noise
voltage, and express it in dB units.
For a positive polarity measurement, repeat the above measurement by changing SW
7B
from a to b.
Note 20:
Reversed polarity center voltage, typical value, inter-axis deviation
Test condition 4 (CP mode)
Input : no signal
Measure the
γ
0 levels of the positive and negative polarities of the output waveform at an output pin
(pin 21 when X = B, pin 19 when X = G, and pin 14 when X = R), and measure the mean value of the
two levels.
Repeat this measurement replacing B, G, and R as the X-axis.
Note 21:
Reversed polarity center voltage, maximum and minimum variable ranges, inter-axis deviation
Test condition 4 (CP mode)
Input : no signal
VR23 :
→
Max /
→
Min
Change SW
25
from a to b, adjust VR26 and set the voltage applied to pin 25 at 5V, thereby
minimizing the cut-off. Change SW
23
from a to b, raise and lower the voltage applied to pin 23 by
turning VR23 clockwise and anticlockwise. Obtain the center voltage of the positive and negative
γ
0
levels when the waveform of an output pin (pin 21 when X = B, pin 19 when X = G and pin 14 when
X = R) approaches V
DD
and stops rising, and set this as the maximum value. Obtain the center
voltage of positive and negative
γ
0 levels when the waveform of the output pin approaches GND and
these levels stop decreasing, and make this voltage the minimum value.
Repeat this measurement replacing B, G, and R as the X-axis.
相關PDF資料 |
PDF描述 |
|---|---|
| TA1242N | TA1242N |
| TA1316AN | YCbCr/YPbPr Signal and Sync Processor for Digital TV, Progressive Scan TV and Double Scan TV |
| TA15.0 | MU-MU FIBER JUMPER SINGLE MODE PVC 5 METER |
| TA10.0 | Beldsol Magnet Wire, Approx. Spool Length: 4060'; Conductor Size AWG:34; Approval Categories:J-W-1177/9; MW 28-C (Single); Conductor Material:Copper; Features:Dual-Insulated with Polyurethane and Nylon Overcoating; Solderable RoHS Compliant: Yes |
| TA2.0 | HIGH-ENERGY TRIGGERED SPARK GAPS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TA1205 | 制造商:Crydom 功能描述: |
| TA1207 | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:FOR LCD TVS, PIF AND SIF SYSTEM |
| TA1207F | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:FOR LCD TVS, PIF AND SIF SYSTEM |
| TA1209F | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:FOR LCD TVS, SEPARATE CARRIER PIF AND SIF SYSTEMS |
| TA120BLKGRN | 制造商:E-Switch Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。