- 您現在的位置：買賣IC網 > PDF目錄383876 > T8531A (Lineage Power) Tone Processing(音調處理器件) PDF資料下載
參數資料
| 型號： | T8531A |
| 廠商： | Lineage Power |
| 英文描述： | Tone Processing(音調處理器件) |
| 中文描述： | 音處理（音調處理器件） |
| 文件頁數： | 15/20頁 |
| 文件大?。?/td> | 338K |
| 代理商： | T8531A |
Lucent Technologies Inc.
15
User Manual
September 2000
T8531 and T8531A Tone Processing
Appendix A: ROM Tone Processing Algorithms
(continued)
Subroutine: CPT Generation Start
Purpose:
Prepares the data for main part of CPT generation subroutine and schedules the
routine for the next frame. CPT generation utilizes a look-up table to generate up
to two frequencies without interpolation.
Start-up Name:
tgen_start
Operation Name:
tgen
TX or RX:
RX
Start-up Address:
0x1000
Operation Address:
0x102B
Function:
Start-up:
1. Checks if CPT time-slot control word is set for present time-slot or if it is 0xCCCC. (Writing 0xCCCC to
address 0x05EF copies the tone information programmed into 0x05F0
—
3 into all 16 channels.)
If not: finishes and calls RX path inactive.
2. Copies control data from CPT control area to CPT operation area for present time slot. Changes RX rtn
address for tgen. Changes TS info. table + 0x10 value. Blanks out RX buffers. Calls RX path inactive.
Operation:
1. Uses a0=ybase value for calculating the control area pointer.
2. Calculates output value and calls rx_in (part of RX path active).
Started by:
host sets rx_rtn address to 0x1000
Terminated by:
host sets the rx_rtn address to RX path inactive routine.
Data Setup Required by Start-up Routine:
Data Storage Locations Altered by Start-up Routine and Required by Operation Routine:
Data Storage Locations Required by Operation Routine:
Data Storage Locations Altered by Operation Routine:
Data Name
tgen_ini_table
Address
0x05EF—0x05F3
Value
see CPT generation specification
Data Name
tgen_time_slot_ini
tgen_table
Data storage for RX filters
rx_rtn
Address
0x05EF
Value
0xFFFF or 0xCCCC if value was 0xCCCC
depends on CPT control area
0x0000
tgen
Tone TS table + 0x0—0x5
TS info. table + 0x15—0x1d
TS info. table + 0x1
Data Name
tproc_address
Address
0x755
Value
RX routine addresses
Data Name
tgen_table
Address
Value
Tone TS table + 0x0—0x5
TS info. table + 0x15—0x1d
depends on CPT control area
NA (altered by RX path active)
Data storage for RX filters
相關PDF資料 |
PDF描述 |
|---|---|
| T8532 | Multichannel Programmable Codec Chip Set(多通道可編程編解碼器芯片組) |
| T8534 | Quad Programmable Line Card Signal Processor(四通道可編程線卡信號處理器) |
| T8533 | Quad Programmable Line Card Signal Processor(四通道可編程線卡信號處理器) |
| T8535A | Quad Programmable Codec Chip Set(四通道可編程編解碼器芯片組) |
| T8536A | Quad Programmable Codec Chip Set(四通道可編程編解碼器芯片組) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T8532 | 制造商:AGERE 制造商全稱:AGERE 功能描述:T8531A/8532 Multichannel Programmable Codec Chip Set |
| T8533 | 制造商:AGERE 制造商全稱:AGERE 功能描述:T8533/34 Quad Programmable Line Card Signal Processor |
| T85331G | 制造商:BITECH 制造商全稱:Bi technologies 功能描述:Thick Film Super Low Profile SIP Resistor Networks |
| T85331J | 制造商:BITECH 制造商全稱:Bi technologies 功能描述:Thick Film Super Low Profile SIP Resistor Networks |
| T8534 | 制造商:AGERE 制造商全稱:AGERE 功能描述:T8533/34 Quad Programmable Line Card Signal Processor |
發布緊急采購，3分鐘左右您將得到回復。