- 您現在的位置：買賣IC網 > PDF目錄297479 > ST68C454CJ68 (EXAR CORP) 4 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PQCC68 PDF資料下載
參數資料
| 型號： | ST68C454CJ68 |
| 廠商： | EXAR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4 CHANNEL(S), 1.5M bps, SERIAL COMM CONTROLLER, PQCC68 |
| 封裝： | PLASTIC, LCC-68 |
| 文件頁數： | 3/29頁 |
| 文件大?。?/td> | 184K |
| 代理商： | ST68C454CJ68 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
ST16C454
11
Rev. 3.30
Programmable Baud Rate Generator
The 454 supports high speed modem technologies that
have increased input data rates by employing data
compression schemes. For example a 33.6Kbps mo-
dem that employs data compression may require a
115.2Kbps input data rate. A 128.0Kbps ISDN modem
that supports data compression may need an input data
rate of 460.8Kbps. The 454 can support a standard data
rate of 921.6Kbps.
Single baud rate generator is provided for the trans-
mitter and receiver, allowing independent TX/RX
channel control. The programmable Baud Rate Gen-
erator is capable of accepting an input clock up to 24
MHz, as required for supporting a 1.5Mbps data rate.
The 454 can be configured for internal or external
clock operation. For internal clock oscillator opera-
tion, an industry standard microprocessor crystal (par-
allel resonant/ 22-33 pF load) is connected externally
between the XTAL1 and XTAL2 pins (see figure 8).
Alternatively, an external clock can be connected to the
XTAL1 pin to clock the internal baud rate generator for
standard or custom rates. (see Baud Rate Generator
Programming).
The generator divides the input 16X clock by any
divisor from 1 to 216 -1. The 454 divides the basic crystal
or external clock by 16. Further division of this 16X clock
provides two table rates to support low and high data
rate applications using the same system design. Cus-
tomized Baud Rates can be achieved by selecting the
proper divisor values for the MSB and LSB sections of
baud rate generator.
Programming the Baud Rate Generator Registers
DLM (MSB) and DLL (LSB) provides a user capability
for selecting the desired final baud rate. The example
in Table 5 below, shows the two selectable baud rate
tables available when using a 1.8432MHz or 7.3728
MHz crystal.
Output
User
DLM
DLL
Baud Rate
16 x Clock
Program
(1.8432 MHz (7.3728 MHz
Divisor
Value
Clock)
(Decimal)
(HEX)
50
200
2304
900
09
00
300
1200
384
180
01
80
600
2400
192
C0
00
C0
1200
4800
96
60
00
60
2400
9600
48
30
00
30
4800
19.2K
24
18
00
18
9600
38.4k
12
0C
00
0C
19.2k
76.8k
6
06
00
06
38.4k
153.6k
3
03
00
03
57.6k
230.4k
2
02
00
02
115.2k
460.8k
1
01
00
01
相關PDF資料 |
PDF描述 |
|---|---|
| ST72F324BK2T6 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32 |
| ST72F324BJ2T5 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP44 |
| ST733C04LCK3LP | 1900 A, 400 V, SCR, TO-200AC |
| ST733C04LCL3P | 1900 A, 400 V, SCR, TO-200AC |
| ST733C04LCN0LP | 1900 A, 400 V, SCR, TO-200AC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST68C554 | 制造商:EXAR 制造商全稱:EXAR 功能描述:QUAD UART WITH 16-BYTE FIFOS |
| ST68C554CJ68 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST68C554CJ68-F | 功能描述:UART 接口集成電路 SIGNALS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST68C554IJ68 | 制造商:Exar Corporation 功能描述: |
| ST68C554IJ68-F | 功能描述:UART 接口集成電路 SIGNALS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。