- 您現在的位置：買賣IC網 > PDF目錄384931 > ST16C650A (Exar Corporation) 2.90V TO 5.5V UART WITH 32-BYTE FIFO PDF資料下載
參數資料
| 型號： | ST16C650A |
| 廠商： | Exar Corporation |
| 英文描述： | 2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| 中文描述： | 2.90V至5.5V UART的32字節FIFO |
| 文件頁數： | 13/53頁 |
| 文件大?。?/td> | 666K |
| 代理商： | ST16C650A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
á
REV. 5.0.0
ST16C650A
2.90V TO 5.5V UART WITH 32-BYTE FIFO
13
2.7
The 650A includes an on-chip oscillator (XTAL1 and XTAL2). The crystal oscillator provides the system clock
to the Baud Rate Generators (BRG) in the UART. XTAL1 is the input to the oscillator or external clock buffer
input with XTAL2 pin being the output. Caution if external clock is used: XTAL1 input is not 5 Volt tolerant. For
programming details, see “Programmable Baud Rate Generator.”
Crystal Oscillator or External Clock
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant,
fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100 ppm frequency
tolerance) connected externally between the XTAL1 and XTAL2 pins (see
Figure 7
). Alternatively, an external
clock can be connected to the XTAL1 pin to clock the internal baud rate generator for standard or custom rates.
Typically, the oscillator connections are shown in
Figure 7
. For further reading on oscillator circuit please see
application note DAN108 on EXAR’s web site.
2.8
Programmable Baud Rate Generator
The UART has its own Baud Rate Generator (BRG) with a prescaler for the transmitter. The prescaler is
controlled by a software bit in the MCR register. The MCR register bit-7 sets the prescaler to divide the input
crystal or external clock by 1 or 4. The clock output of the prescaler goes to the BRG. The BRG further divides
this clock by a programmable divisor between 1 and (2
16
-1) to obtain a 16X sampling clock of the serial data
rate. The sampling clock is used by the transmitter for data bit shifting and
receiver for data sampling. The
BRG divisor (DLL and DLM registers) defaults to a random value upon power up or a reset. Therefore, the
BRG must be programmed during initialization to the operating data rate.
F
IGURE
7. T
YPICAL
OSCILLATOR
CONNECTIONS
C1
22-47 pF
C2
22-47 pF
Y1
1.8432 MHz
to
24 MHz
R1
0-120
(Optional)
R2
500 Κ 1 Μ
XTAL1
XTAL2
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C650ACJ44 | 2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650ACP40 | 2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650ACQ48 | 2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650AIJ44 | 2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650AIP40 | 2.90V TO 5.5V UART WITH 32-BYTE FIFO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C650A_0508 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650A_09 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO |
| ST16C650ACJ44 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C650ACJ44-F | 功能描述:UART 接口集成電路 UART W/32BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C650ACJ44TR-F | 功能描述:UART 接口集成電路 UART W/32BYTE FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。