- 您現在的位置：買賣IC網 > PDF目錄98142 > SST85LP1004B-M-C-LFTE IDE COMPATIBLE, FLASH MEMORY DRIVE CONTROLLER, PBGA91 PDF資料下載
參數資料
| 型號： | SST85LP1004B-M-C-LFTE |
| 元件分類： | 存儲控制器/管理單元 |
| 英文描述： | IDE COMPATIBLE, FLASH MEMORY DRIVE CONTROLLER, PBGA91 |
| 封裝： | 14 X 24 MM, 1.30 MM HEIGHT, ROHS COMPLIANT, BGA-91 |
| 文件頁數： | 19/36頁 |
| 文件大?。?/td> | 910K |
| 代理商： | SST85LP1004B-M-C-LFTE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
2010 Silicon Storage Technology, Inc.
S71420-01-000
04/10
26
4 GByte NANDrive
SST85LP1004B
Advance Information
Features 02H and 82H allow the host to enable or disable write cache in the NANDrives that imple-
ment write cache. When the subcommand Disable-Write-Cache is issued, the NANDrive should ini-
tiate the sequence to flush cache to non-volatile memory before command completion.
Feature 03H allows the host to select the transfer mode by specifying a value in the Sector Count reg-
ister. The upper 5 bits define the type of transfer and the low order 3 bits encode the mode value. One
PIO mode is selected at all times. The host may change the selected modes by the Set-Features com-
mand.
Feature 55H is the default feature for the NANDrive. Therefore, the host does not have to issue Set-
Features command with this feature unless it is necessary for compatibility reasons.
Features 66H and CCH can be used to enable and disable whether the Power-on Reset (POR)
Defaults will be set when a software reset occurs.
Idle - 97H or E3H
This command causes the NANDrive to set BSY, enter the Idle mode, clear BSY and generate an
interrupt. If the sector count is non-zero, it is interpreted as a timer count with each count being 5 milli-
seconds and the automatic Power-down mode is enabled. If the sector count is zero, the automatic
Power-down mode is also enabled, the timer count is set to 3, with each count being 5 ms. Note that
this time base (5 msec) is different from the ATA specification.
Table 10: Transfer Mode Values
Mode
Bits [7:3]
Bits [2:0]
PIO default mode
00000b
000b
PIO default mode, disable IORDY
00000b
001b
PIO flow control transfer mode
00001b
mode1
1. Mode = transfer mode number, all other values are not valid
Multi-word DMA mode
00100b
mode1
Ultra-DMA mode
01000b
mode1
Reserved
Other
N/A
T10.1 1420
Bit ->
76
543210
Command (7)
97H or E3H
C/D/H (6)
XDrive
X
Cyl High (5)
X
Cyl Low (4)
X
Sec Num (3)
X
Sec Cnt (2)
Timer Count (5 msec increments)
Feature (1)
X
相關PDF資料 |
PDF描述 |
|---|---|
| SST89C58-33-I-TQJE | 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQFP44 |
| SST89E516RD-40-C-QIF | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, QCC40 |
| SST89E516RD2-40-C-NJE | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQCC44 |
| SST89E52RD-40-C-PI | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PDIP40 |
| SST89V58RD-33-C-PI | 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PDIP40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SST85LP1016B-M-C-FTE | 功能描述:閃存 16G NAND 3.3V Commercial RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| SST88VP1107 | 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:All-in-OneMemory |
| SST88VP1107-80-5C-LBSE | 功能描述:組合存儲器 NOR/NAND/PSRAM 80MHz 2.7V Commercial RoHS:否 制造商:Microchip Technology 組織:512 K x 16 電源電壓-最大: 電源電壓-最小: 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:LFBGA-48 封裝:Tray |
| SST88VP1107-80-5W-LBSE | 功能描述:組合存儲器 NOR/NAND/PSRAM 80MHz 2.7V Wireless RoHS:否 制造商:Microchip Technology 組織:512 K x 16 電源電壓-最大: 電源電壓-最小: 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:LFBGA-48 封裝:Tray |
| SST89C54 | 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:FlashFlex51 MCU |
發布緊急采購，3分鐘左右您將得到回復。