- 您現在的位置：買賣IC網 > Datasheet目錄46 > SE95D,112 (NXP Semiconductors)IC SENSOR TEMP 2.8-5.5V SOT96-1 Datasheet資料下載
參數資料
| 型號： | SE95D,112 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 7/27頁 |
| 文件大?。?/td> | 150K |
| 描述： | IC SENSOR TEMP 2.8-5.5V SOT96-1 |
| 標準包裝： | 100 |
| 功能： | 溫度監視系統（傳感器），監視器 |
| 傳感器類型： | 內部 |
| 感應溫度： | -55°C ~ 125°C |
| 精確度： | ±3°C（最小值） |
| 拓?fù)洌?/td> | ADC（三角積分型），比較器，振蕩器，寄存器庫 |
| 輸出類型： | 2 線串行，I²C? |
| 輸出警報： | 無 |
| 輸出風扇： | 是 |
| 電源電壓： | 2.8 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 管件 |
| 其它名稱： | 935274141112 SE95D SE95D-ND |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
SE95_7
?NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07 2 September 2009
7 of 27
NXP Semiconductors
SE95
Ultra high accuracy digital temperature sensor and thermal watchdog
7.5 Shutdown mode
The device operation mode is selected by programming bit SHUTDOWN of register Conf.
Setting bit SHUTDOWN to logic 1 will put the device into shutdown mode. Resetting bit
SHUTDOWN to logic 0 will return the device to normal mode.
In shutdown mode, the device draws a small current of approximately 7.5 礎 and the
power dissipation is minimized; the temperature conversion stops, but the I
2
C-bus
interface remains active and register write/read operation can be performed. If the OS
output is in comparator mode, then it remains unchanged. In interrupt mode, the OS
output is reset.
7.6 Power-up default and power-on reset
The SE95 always powers-up in its default state with:
" Normal operation mode
" OS comparator mode
" T
os
= 80 癈
" T
hyst
= 75 癈
" OS output active state is LOW
" Pointer value is logic 0
When the power supply voltage is dropped below the device power-on reset level of
approximately 1.9 V (POR) and then rises up again, the device will be reset to its default
condition as listed above.
8. I
2
C-bus serial interface
The SE95 can be connected to a compatible 2-wire serial interface I
2
C-bus as a slave
device under the control of a controller or master device, using two device terminals, SCL
and SDA. The controller must provide the SCL clock signal and write/read data to and
from the device through the SDA terminal. Note that if the I
2
C-bus common pull-up
resistors have not been installed as required for I
2
C-bus, then an external pull-up resistor,
approximately 10 k&, is needed for each of these two terminals. The bus communication
protocols are described in
Section 8.7 Protocols f
or wr
iting and reading the registers .
8.1 Slave address
The SE95 slave address on the I
2
C-bus is partially dened by the logic applied to the
device address pins A2, A1 and A0. Each pin is typically connected either to GND for
logic 0, or to V
CC
for logic 1. These pins represent the three LSB bits of the device 7-bit
address. The other four MSB bits of the address data are preset to 1001 by hard wiring
inside the SE95.
T
ab
le
4 shows the device's complete address and indicates that up to
8 devices can be connected to the same bus without address conict. Because the input
pins SCL, SDA and A2 to A0, are not internally biased, it is important that they should not
be left oating in any application.
0Ch is a reserved address for SMBus Alert Response Address (ARA). This is an optional
command from the SMBus specication to allow SMBus devices to respond to an SMBus
master with their slave device if they are generating an interrupt. The SE95 will send a
相關PDF資料 |
PDF描述 |
|---|---|
| SE97BTP,547 | IC TEMP SENSOR DIMM 8HWSON |
| SE98ATP,547 | IC TEMP SENSOR DDR 8-HWSON |
| SG6901ASZ | IC PFC CTLR AVERAGE CURR 20SOIC |
| SG6932SZ | IC PFC CONTROLLER CCM 16SOP |
| SG6961SY | IC PFC CTRLR AVERAGE CURR 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SE95D118 | 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
| SE95DP | 制造商:NXP Semiconductors 功能描述:IC TEMP SENSOR DIGITAL 8TSSOP 制造商:NXP Semiconductors 功能描述:IC, TEMP SENSOR, DIGITAL, 8TSSOP 制造商:NXP Semiconductors 功能描述:IC, TEMP SENSOR, DIGITAL, 8TSSOP; IC Output Type:Digital; Sensing Accuracy Range: 2C; Sensing Temperature Min:-55C; Sensing Temperature Max:+125C; Supply Voltage Min:2.8V; Supply Voltage Max:5.5V; Sensor Case Style:TSSOP; No. of ;RoHS Compliant: Yes |
| SE95DP,118 | 功能描述:板上安裝溫度傳感器 TEMP SENSOR DIGITAL RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| SE95DP,118-CUT TAPE | 制造商:NXP 功能描述:SE95D Series 2.8 V to 5.5 V 1% Accuracy Digital Temperature Sensor - TSSOP-8 |
| SE95DP118 | 制造商:NXP Semiconductors 功能描述:DIGITAL TEMP SENSOR IC 11BIT +/-3C TS |
發布緊急采購，3分鐘左右您將得到回復。