參數資料
型號： SE95D,112
廠商： NXP Semiconductors
文件頁數： 5/27頁
文件大?。?/td> 150K
描述： IC SENSOR TEMP 2.8-5.5V SOT96-1
標準包裝： 100
功能： 溫度監視系統（傳感器），監視器
傳感器類型： 內部
感應溫度： -55°C ~ 125°C
精確度： ±3°C（最小值）
拓?fù)洌?/td> ADC（三角積分型），比較器，振蕩器，寄存器庫
輸出類型： 2 線串行，I²C?
輸出警報： 無
輸出風扇： 是
電源電壓： 2.8 V ~ 5.5 V
工作溫度： -55°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 8-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 8-SO
包裝： 管件
其它名稱： 935274141112
SE95D
SE95D-ND
SE95_7
?NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 07  2 September 2009
5 of 27
NXP Semiconductors
SE95
Ultra high accuracy digital temperature sensor and thermal watchdog
In OS interrupt mode, the OS output is used for thermal interruption. When the device is
powered-up, the OS output is rst activated only when Temp exceeds T
os
; then it remains
active indenitely until being reset by a read of any register. Once the OS output has been
activated by crossing T
os
and then reset, it can be activated again only when Temp drops
below T
hyst
; then again, it remains active indenitely until being reset by a read of any
register. The OS interrupt operation would be continued in this sequence: T
os
 trip, reset,
T
hyst
 trip, reset, T
os
 trip, reset, T
hyst
 trip, reset, and etc. Putting the device into shutdown
mode also resets the OS output.
In both cases, comparator mode and interrupt mode, the OS output is activated only if a
number of consecutive faults, dened by the device fault queue, has been met. The fault
queue is programmable and stored in bits OS_F_QUE[1:0], of register Conf. Also, the OS
output active state is selectable as HIGH or LOW by setting accordingly the bit OS_POL
of register Conf.
At power-up, the device is put into normal operation mode, register Tos is set to 80 癈,
register Thyst is set to 75 癈, OS active state is selected LOW and the fault queue is equal
to 1. The data reading of register Temp is not available until the rst conversion is
completed in about 33 ms.
The OS response to the temperature is illustrated in
Figure
4.
(1)  OS is reset by either reading register or putting the device in shutdown mode. Assumed that the
fault queue is met at each T
os
 and T
hyst
 crossing point.
Fig 4.    OS response to temperature
001aad623
(1)
(1)
(1)
T
os
T
hyst
OS RESET
OS ACTIVE
OS RESET
OS ACTIVE
OS output in comparator mode
OS output in interrupt mode
reading temperature limits
相關PDF資料
PDF描述
SE97BTP,547 IC TEMP SENSOR DIMM 8HWSON
SE98ATP,547 IC TEMP SENSOR DDR 8-HWSON
SG6901ASZ IC PFC CTLR AVERAGE CURR 20SOIC
SG6932SZ IC PFC CONTROLLER CCM 16SOP
SG6961SY IC PFC CTRLR AVERAGE CURR 8SOIC
相關代理商/技術參數
參數描述
SE95D118 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述:
SE95DP 制造商:NXP Semiconductors 功能描述:IC TEMP SENSOR DIGITAL 8TSSOP 制造商:NXP Semiconductors 功能描述:IC, TEMP SENSOR, DIGITAL, 8TSSOP 制造商:NXP Semiconductors 功能描述:IC, TEMP SENSOR, DIGITAL, 8TSSOP; IC Output Type:Digital; Sensing Accuracy Range: 2C; Sensing Temperature Min:-55C; Sensing Temperature Max:+125C; Supply Voltage Min:2.8V; Supply Voltage Max:5.5V; Sensor Case Style:TSSOP; No. of ;RoHS Compliant: Yes
SE95DP,118 功能描述:板上安裝溫度傳感器 TEMP SENSOR DIGITAL RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
SE95DP,118-CUT TAPE 制造商:NXP 功能描述:SE95D Series 2.8 V to 5.5 V 1% Accuracy Digital Temperature Sensor - TSSOP-8
SE95DP118 制造商:NXP Semiconductors 功能描述:DIGITAL TEMP SENSOR IC 11BIT +/-3C TS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*