- 您現在的位置：買賣IC網 > PDF目錄385814 > SAB88C166W-5M (SIEMENS A G) 16-Bit CMOS Single-Chip Microcontrollers with/without oscillator prescaler with 32 KByte Flash EPROM PDF資料下載
參數資料
| 型號： | SAB88C166W-5M |
| 廠商： | SIEMENS A G |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-Bit CMOS Single-Chip Microcontrollers with/without oscillator prescaler with 32 KByte Flash EPROM |
| 中文描述： | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 |
| 文件頁數： | 16/58頁 |
| 文件大?。?/td> | 611K |
| 代理商： | SAB88C166W-5M |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
SAB 88C166(W)
Semiconductor Group
15
In Flash Programming Mode
(FEE=’0’, FWE=’1’) the SAB 88C166(W) is prepared to program
Flash locations in the way specified by the Word or Double Word Write (WDWW) bit in the FCR. The
width of the programming pulses generated internally is defined by the Internal Flash Timer Clock
Control (CKCTL) bit field of the FCR. The maximum number of programming pulses (PN
max
)
applied to the Flash memory is determined by software in the Flash programming algorithm. The
chosen values for CKCTL and PN
max
must guarantee a maximum cumulated programming time of
2.5 ms per cell and a maximum programming pulse width of 200
μ
s.
If 16-bit programming was selected, the operation will start automatically when an instruction is
executed, where the first operand specifies the address and the second operand the value to be
programmed:
MOV
If 32-bit programming was selected, the operation will start automatically when the second of two
subsequent instructions is executed, which define the doubleword to be programmed. Note that the
destination pointers of both instructions refer to the same even double word address. The two
instructions must be executed without any interruption.
[Rw
n
], Rw
m
; Program one word
MOV
MOV
Upon the execution of the second instruction (the one and only in 16-bit programming mode), the
Flash Busy (FBUSY) bit is automatically set to ‘1’. End of programming can be detected by polling
the FBUSY bit. V
PP
must stay within the valid margins during the entire programming process.
At the end of programming the Program-Verify-Mode
(PVM)
is entered automatically. This mode
allows to check the effect of the erase operation (see description below).
[Rw
n
], Rw
x
[Rw
n
], Rw
y
; Prepare programming of first word
; Start programming of both words
The Flash Verify-Modes
Erase-Verify-Mode (EVM) and Program-Verify-Mode (PVM) allow to
verify the effect of an erase or programming operation. In these modes an internally generated
margin voltage is applied to a Flash cell, which makes reading more critical than for standard read
accesses. This ensures safe standard accesses after correct verification.
To get the contents of a Flash word in this mode, it has to be read in a particular way:
MOV
…
MOV
Rw
m
, [Rw
n
]
; First (invalid) read of dedicated cell
; 4
μ
s delay to stabilize internal margin voltage
; Second (valid) read of dedicated cell
Rw
m
, [Rw
n
]
Such a Flash verify read operation is different from the reading in the standard or in the non-verify
mode. Correct verify reading needs a read operation performed twice on the same cell with an
absolute time delay of 4
μ
s which is needed to stabilize the internal margin voltage applied to the
cell. To verify that a Flash cell was erased or programmed properly, the value of the second verify
read operation has to be compared against FFFF
H
or the target value, respectively. Clearing bit
FWE to ‘0’ exits the Flash programming mode and returns to the Flash non-verify mode.
In Flash non-verify mode
all Flash locations can be read as usual (via indirect addressing modes),
which is not possible in Flash programming or Flash erase mode (see EVM and PVM).
相關PDF資料 |
PDF描述 |
|---|---|
| SAB88C166 | 16-Bit CMOS Single-Chip Microcontrollers with/without oscillator prescaler with 32 KByte Flash EPROM |
| SAB88C166-5M | 16-Bit CMOS Single-Chip Microcontrollers with/without oscillator prescaler with 32 KByte Flash EPROM |
| SAE 81C90 | 16-Bit Microcontroller(16位微控制器) |
| SAE 81C91 | 16-bit microcontrollers(16位微控制器) |
| SAF-C167CR-16F | 16-Bit CMOS Single-Chip Microcontroller with 128KByte Flash EPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAB9075H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Picture-in-Picture PIP controller for NTSC |
| SAB9075HB-S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Picture-in-Picture Circuit |
| SAB9076H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Picture-In-Picture PIP controller |
| SAB9077 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Picture-In-Picture PIP controller |
| SAB9077H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Picture-In-Picture PIP controller |
發布緊急采購，3分鐘左右您將得到回復。