參數資料
型號： SAA8122A
廠商： NXP Semiconductors N.V.
英文描述： Digital Still Camera Processor (ImagIC family)(數字靜態照相處理器)
中文描述： 數碼相機處理器（夢想家家庭）（數字靜態照相處理器）
文件頁數： 23/26頁
文件大?。?/td> 885K
代理商： SAA8122A
Philips Semiconductors
SAA8122A
Digital Still Camera Processor (ImagIC family)
Objective specification
Rev. 01 — 20 April 2000
23 of 26
9397 750 07048
Philips Electronics N.V. 2000. All rights reserved.
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time is 4 seconds at 250
°
C. A mildly-activated flux will eliminate the
need for removal of corrosive residues in most applications.
10.4 Manual soldering
Fix the component by first soldering two diagonally-opposite end leads. Use a low
voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time
must be limited to 10 seconds at up to 300
°
C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 to 5 seconds between 270 and 320
°
C.
10.5 Package related soldering information
[1]
All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the
maximum temperature (with respect to time) and body size of the package, there is a risk that internal
or external package cracks may occur due to vaporization of the moisture in them (the so called
popcorn effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated
Circuit Packages; Section: Packing Methods
These packages are not suitable for wave soldering as a solder joint between the printed-circuit board
and heatsink (at bottom version) can not be achieved, and as solder may stick to the heatsink (on top
version).
If wave soldering is considered, then the package must be placed at a 45
°
angle to the solder wave
direction. The package footprint must incorporate solder thieves downstream and at the side corners.
Wave soldering is only suitable for LQFP, QFP and TQFP packages with a pitch (e) equal to or larger
than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.
Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than
0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.
[2]
[3]
[4]
[5]
11. Revision history
Table 7:
Suitability of surface mount IC packages for wave and reflow soldering
methods
Soldering method
Wave
BGA, LFBGA, SQFP, TFBGA
HBCC, HLQFP, HSQFP, HSOP, HTQFP,
HTSSOP, SMS
PLCC
[3]
, SO, SOJ
LQFP, QFP, TQFP
SSOP, TSSOP, VSO
Package
Reflow
[1]
suitable
suitable
not suitable
not suitable
[2]
suitable
not recommended
[3][4]
not recommended
[5]
suitable
suitable
suitable
Table 8:
Rev Date
01
Revision history
CPCN
20000420
Description
Objective specification; initial version
-
相關PDF資料
PDF描述
SAA8122AEL Digital Still Camera Processor ImagIC family
SAB-C504-2R24M 8-Bit CMOS Microcontroller
SAB-C504-2R40M 8-Bit CMOS Microcontroller
SAB-C504-2RM 8-Bit CMOS Microcontroller
SAB-C504-L24M 8-Bit CMOS Microcontroller
相關代理商/技術參數
參數描述
SAA8122AEL 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital Still Camera Processor ImagIC family
SAA8122E 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital Still Camera
SAA8122E/C1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital Still Camera
SAA8200HL 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Ensation Base integrated wireless audio baseband
SAA8200HL/N100,518 制造商:ST-Ericsson 功能描述:SAA8200HL Series Ensation Base Integrated Wireless Audio Baseband - LQFP-100
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*