參數資料
型號： SAA7327
廠商： NXP Semiconductors N.V.
英文描述： Digital servo processor and Compact Disc decoder with integrated DAC for video CD (CD7 II)(應用于視頻CD的帶綜合數模轉換器（DAC）的數字伺服處理器和光盤譯碼器)
中文描述： 數字伺服處理器和光盤解碼器集成了用于視頻光盤（CD7抗原二）（應用于視頻光碟的帶綜合數模轉換器（DAC）的的數字伺服處理器和光盤譯碼器援會）
文件頁數： 33/68頁
文件大?。?/td> 284K
代理商： SAA7327
2000 Jun 26
33
Philips Semiconductors
Product specification
Digital servo processor and Compact Disc
decoder with integrated DAC for video CD (CD7 II)
SAA7327
7.15.1
M
ICROCONTROLLER INTERFACE
(4-
WIRE BUS MODE
)
7.15.1.1
Writing data to registers 0 to F
The sixteen 4-bit programmable configuration registers,
0 to F (see Table 14), can be written to via the
microcontroller interface using the protocol shown in
Fig.23.
It should be noted that SILD must be held HIGH; A3 to A0
identifies the register number and D3 to D0 is the data.
The data is latched into the register on the LOW-to-HIGH
transition of RAB.
7.15.1.2
Writing repeated data to registers 0 to F
The same data can be repeated several times (e.g. for a
fade function) by applying extra RAB pulses as shown in
Fig.24. It should be noted that SCL must stay HIGH
between RAB pulses.
7.15.1.3
Reading decoder status information on SDA
There are several internal status signals, selected via
register 2, which can be made available on the SDA line:
SUBQREADY-I: LOW if new subcode word is ready in
Q-channel register
MOTSTART1: HIGH if motor is turning at 75% or more
of nominal speed
MOTSTART2: HIGH if motor is turning at 50% or more
of nominal speed
MOTSTOP: HIGH if motor is turning at 12% or less of
nominal speed; can be set to indicate 6% or less
(instead of 12% or less) via register E
PLL lock: HIGH if sync coincidence signals are found
V1: follows input on pin V1
V2: follows input on pin V2
MOTOR-OV: HIGH if the motor servo output stage
saturates
FIFO-OV: HIGH if FIFO overflows
SHOCK: MOTSTART2 + PLL Lock + MOTOR-OV +
FIFO-OV + servo interrupt signal + OTD (HIGH if shock
detected)
LA-SHOCK: latched SHOCK signal.
The status read protocol is shown in Fig.25. It should be
noted that SILD must be held HIGH.
7.15.1.4
Reading Q-channel subcode
To read the Q-channel subcode direct in the 4-wire bus
mode, the SUBQREADY-I signal should be selected as
status signal. The subcode read protocol is illustrated in
Fig.26.
It should be noted that SILD must be held HIGH; after
subcode read starts, the microcontroller may take as long
as it wants to terminate the read operation; when enough
subcodehasbeenread(1 to 96 bits),terminatereadingby
pulling RAB LOW.
Alternatively, the Q-channel subcode can be read using a
servo command as follows:
Use the read high-level status command to monitor the
subcode ready signal
Send the read subcode command, and read the
required number of bytes (up to 12)
Send the read high-level status command; to re-enable
the decoder interface.
7.15.1.5
Behaviour of the SUBQREADY-I signal
When the CRC of the Q-channel word is good, and no
subcode is being read, the SUBQREADY-I status signal
will react as shown in Fig.27. When the CRC is good and
the subcode is being read, the timing in Fig.28 applies.
If t
1
(SUBQREADY-I status LOW to end of subcode read)
is below 2.6/n ms, then t
2
= 13.1/n ms (i.e.: the
microcontroller can read all subcode frames if it completes
the read operation within 2.6/n ms after the subcode is
ready). If these criteria are not met, it is only possible to
guarantee that t
3
will be below 26.2/n ms (approximately).
If subcode frames with failed CRCs are present, the
t
2
and t
3
times will be increased by 13.1/n ms for each
defective subcode frame.
It should be noted that in the lock-to-disc mode ‘n’ is
replaced by ‘d’, which is the disc speed factor.
7.15.1.6
Write servo commands
A write data command is used to transfer data (a number
of bytes) from the microcontroller, using the protocol
shown in Fig.29. The first of these bytes is the command
byte and the following are data bytes; the number
(between 1 and 7) depends on the command byte.
相關PDF資料
PDF描述
SAA7335GP DSP for CD and DVD-ROM systems
SAA7335 DSP for CD and DVD-ROM systems(在CD和DVD-ROM應用中的DSP)
SAA7341 COMS Digital decoding IC for Compact Disc
SAA7341GP COMS Digital decoding IC for Compact Disc
SAA7345 Bitstream conversion ADC for digital audio systems
相關代理商/技術參數
參數描述
SAA7327H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital servo processor and Compact Disc decoder with integrated DAC for video CD CD7 II
SAA7327H/T/M2B,557 功能描述:視頻 IC COMPACT DISC SYSTEMS RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel
SAA7327HBG 功能描述:視頻 IC COMPACT DISC SYSTEMS RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel
SAA7335 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DSP for CD and DVD-ROM systems
SAA7335GP 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DSP for CD and DVD-ROM systems
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*