參數資料
型號： SAA7326H
廠商： NXP SEMICONDUCTORS
元件分類： 消費家電
英文描述： CABLE ASSEMBLY; TNC MALE TO TNC MALE; 75 OHM, RG59B/U COAX; 12" CABLE LENGTH; *USES STANDARD 50 OHM INTERFACE CONNECTORS*
中文描述： SPECIALTY CONSUMER CIRCUIT, PQFP64
封裝： PLASTIC, SOT-393-1, QFP-64
文件頁數： 34/68頁
文件大?。?/td> 391K
代理商： SAA7326H
1999 Jun 17
34
Philips Semiconductors
Product specification
Digital servo processor and Compact Disc
decoder with integrated DAC (CD10)
SAA7326
7.15.1.6
Write servo commands
A write data command is used to transfer data (a number
of bytes) from the microcontroller, using the protocol
shown in Fig.29. The first of these bytes is the command
byte and the following are data bytes; the number
(between 1 and 7) depends on the command byte.
It should be noted that RAB must be held LOW; the
command or data is interpreted by the SAA7326 after the
HIGH-to-LOW transition of SILD; there must be a
minimum time of 70
μ
s between SILD pulses.
7.15.1.7
Writing repeated data in servo commands
The same data byte can be repeated by applying extra
SILD pulses as illustrated in Fig.30. SCL must be HIGH
between the SILD pulses.
7.15.1.8
Read servo commands
A read data command is used to transfer data (status
information) to the microcontroller, using the protocol
shown in Fig.31. The first byte written determines the type
of command. After this byte a variable number of bytes can
be read. It should be noted that RAB must be held LOW;
after the end of the command byte (LOW-to-HIGH
transition on SILD) there must be a delay of 70
μ
s before
reading data is started (i.e. the next HIGH-to-LOW
transition on SILD); there must be a minimum time of 70
μ
s
between SILD pulses.
7.15.2
M
ICROCONTROLLER INTERFACE
(I
2
C-
BUS MODE
)
Bytes are transferred over the interface in groups
(i.e. servo commands) of which there are two types: write
data commands and read data commands.
The sequence for a write data command (that requires
3 data bytes) is as follows:
Send START condition
Send address 30H (write)
Write command byte
Write data byte 1
Write data byte 2
Write data byte 3
Send STOP condition.
It should be noted that more than one command can be
sent in one write sequence.
The sequence for a read data command (that reads 2 data
bytes) is as follows:
Send START condition
Send address 30H (write)
Write command byte
Send STOP condition
Send START condition
Send address 31H (read)
Read data byte 1
Read data byte 2
Send STOP condition.
It should be noted that the timing constraints specified for
the read and write servo commands must still be adhered
to.
Fig.23 Microcontroller write protocol for registers 0 to F.
A3
A2
A1
A0
D3
D2
D1
D0
SDA
(SAA7326)
SCL
(microcontroller)
RAB
(microcontroller)
SDA
(microcontroller)
MGL699
high-impedance
相關PDF資料
PDF描述
SAA7327 Digital servo processor and Compact Disc decoder with integrated DAC for video CD (CD7 II)(應用于視頻CD的帶綜合數模轉換器（DAC）的數字伺服處理器和光盤譯碼器)
SAA7335GP DSP for CD and DVD-ROM systems
SAA7335 DSP for CD and DVD-ROM systems(在CD和DVD-ROM應用中的DSP)
SAA7341 COMS Digital decoding IC for Compact Disc
SAA7341GP COMS Digital decoding IC for Compact Disc
相關代理商/技術參數
參數描述
SAA7327 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital servo processor and Compact Disc decoder with integrated DAC for video CD CD7 II
SAA7327H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital servo processor and Compact Disc decoder with integrated DAC for video CD CD7 II
SAA7327H/T/M2B,557 功能描述:視頻 IC COMPACT DISC SYSTEMS RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel
SAA7327HBG 功能描述:視頻 IC COMPACT DISC SYSTEMS RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel
SAA7335 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:DSP for CD and DVD-ROM systems
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*