參數資料
型號： SAA7325H
廠商： NXP SEMICONDUCTORS
元件分類： 消費家電
英文描述： Digital servo processor and Compact Disc decoder with integrated DAC CD10
中文描述： SPECIALTY CONSUMER CIRCUIT, PQFP64
封裝： PLASTIC, SOT-393-1, QFP-64
文件頁數： 31/68頁
文件大?。?/td> 273K
代理商： SAA7325H
1999 Jun 17
31
Philips Semiconductors
Product specification
Digital servo processor and Compact Disc
decoder with integrated DAC (CD10)
SAA7325
7.14.7
O
FF
-
TRACK DETECTION
During active radial tracking, off-track detection has been
realised by continuously monitoring the off-track counter
value. The off-track flag becomes valid whenever the
off-track counter value is not equal to zero. Depending on
the type of extended S-curve, the off-track counter is reset
after 0.75 extend or at the original track in the 2.25 track
extend mode.
7.14.8
H
IGH
-
LEVEL FEATURES
7.14.8.1
Interrupt mechanism and STATUS pin
The STATUS pin is an output which is active LOW, its
output is selected by decoder register 7 to be either the
decoder status bit (active LOW) selected by decoder
register 2 (only available in 4-wire bus mode) or the
interrupt signal generated by the servo part.
8 signals from the interrupt status register are selectable
from the servo part via the interrupt_mask parameter.
The interrupt is reset by sending the read high-level status
command. The 8 signals are as follows:
Focus lost: dropout of longer than 3 ms
Subcode ready
Subcode absolute seconds changed
Subcode discontinuity detected: new subcode time
before previous subcode time, or more than 10 frames
later than previous subcode time
Radial error: during radial on-track, no new subcode
frame occurs within time defined by the playwatchtime
parameter; during radial jump, less than 4 tracks have
been crossed during time defined by the jumpwatchtime
parameter
Autosequencer state change
Autosequencer error
Subcode interface blocked: the internal decoder
interface is being used.
It should be noted that if the STATUS pin output is selected
via decoder register 2 and either the microcontroller writes
a different value to decoder register 2 or the decoder
interface is enabled then the STATUS output will change.
7.14.8.2
Decoder interface
The decoder interface allows decoder registers 0 to F to
be programmed and subcode Q-channel data to be read
via servo commands. The interface is enabled/disabled by
the preset latch command (and the xtra_preset
parameter).
7.14.8.3
Automatic error handling
Three Watchdogs are present:
Focus: detects focus drop out of longer than 3 ms, sets
focus lost interrupt, switches off radial and sledge
servos, disables drive to disc motor
Radial play: started when radial servo is in on-track
mode and a first subcode frame is found; detects when
maximum time between two subcode frames exceeds
time set by playwatchtime parameter; then sets radial
error interrupt, switches radial and sledge servos off,
puts disc motor in jump mode
Radial jump: active when radial servo is in long jump or
short jump modes. Detects when the off-track counter
value decreases by less than 4 tracks between two
readings (time interval set by jumpwatchtime
parameter); then sets radial jump error, switches radial
and sledge servos off to cancel jump
The focus Watchdog is always active, the radial
Watchdogs are selectable via the radcontrol parameter.
7.14.8.4
Automatic sequencers and timer interrupts
Two automatic sequencers are implemented (and must be
initialized after power-on):
Autostart sequencer: controls the start-up of focus,
radial and motor
Autostop sequencer: brakes the disc and shuts down
servos.
When the automatic sequencers are not used it is possible
to generate timer interrupts, defined by the
time_parameter coefficient.
7.14.8.5
High-level status
The read high-level status command can be used to obtain
the interrupt, decoder, autosequencer status registers and
the motor start time. Use of the read high-level status
command clears the interrupt status register, and
re-enables the subcode read via a servo command.
7.14.9
D
RIVER INTERFACE
The control signals (pins RA, FO and SL) for the
mechanism actuators are pulse density modulated.
The modulating frequency can be set to either
1.0584 (DSD mode) or 2.1168 MHz; controlled via the
xtra_preset parameter. An analog representation of the
output signals can be achieved by connecting a 1st-order
low-pass filter to the outputs.
相關PDF資料
PDF描述
SAA7326H CABLE ASSEMBLY; TNC MALE TO TNC MALE; 75 OHM, RG59B/U COAX; 12" CABLE LENGTH; *USES STANDARD 50 OHM INTERFACE CONNECTORS*
SAA7327 Digital servo processor and Compact Disc decoder with integrated DAC for video CD (CD7 II)(應用于視頻CD的帶綜合數模轉換器（DAC）的數字伺服處理器和光盤譯碼器)
SAA7335GP DSP for CD and DVD-ROM systems
SAA7335 DSP for CD and DVD-ROM systems(在CD和DVD-ROM應用中的DSP)
SAA7341 COMS Digital decoding IC for Compact Disc
相關代理商/技術參數
參數描述
SAA7326 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital servo processor and Compact Disc decoder with integrated DAC CD10
SAA7326H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital servo processor and Compact Disc decoder with integrated DAC CD10
SAA7327 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital servo processor and Compact Disc decoder with integrated DAC for video CD CD7 II
SAA7327H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital servo processor and Compact Disc decoder with integrated DAC for video CD CD7 II
SAA7327H/T/M2B,557 功能描述:視頻 IC COMPACT DISC SYSTEMS RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*