- 您現在的位置：買賣IC網 > PDF目錄98070 > S3C1860XX-DK 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDIP20 PDF資料下載
參數資料
| 型號： | S3C1860XX-DK |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDIP20 |
| 封裝： | 0.300 INCH, DIP-20 |
| 文件頁數： | 58/95頁 |
| 文件大?。?/td> | 339K |
| 代理商： | S3C1860XX-DK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁
REMOTE CONTROL TX. APPLICATION NOTE
S3C1840/C1850/C1860/P1860
7-4
Automatic Reset by Halt Mode Release
This function resets the CPU by releasing Halt mode. The CPU is reset to its initial operating status and program
execution starts from the reset address.
Halt Mode and Automatic Reset by Halt Release
Halt mode is used to reduce power consumption by stopping the oscillation and holding the internal state. Halt
mode can be entered by forcing IP2.12 to high level (remaining input pins are non-active).
Before entering Halt mode, programmer should pre-set all key strobe output pins to active state even though Halt
mode causes some pins to remain active.
For the 24 pins, P3.0-P3.3, P2.0, P2.2- P2.4, and P2.5 are sent low and for 20 pins, P3.0-P3.3, P2.0, P2.2-P2.4
are sent low, but the P2.0 is floating state in S3C1850/C1860.. Forcing any key input port to active state causes
the clock oscillation logic to start system initialization.
At this time, the system is reset after the oscillation stabilization time elapses. A system reset causes program
execution to start from address 0F00H.
Normal Mode:
After a reset, the program
restarts from 0F00H after one
instruction in 0FxxH is
executed.('F' is page number
and 'xx' is the instruction
immediately following the
HALT instruction.)
Halt Release Signal
IP2.12 = 1, Non-Active Input Pin
Normal Mode
Halt
XO
Osc. Circuit
Wait Time
(3-4 ms)
Osc. Stabilization Timer Start
Osc. Stabilization Timer
(9 ms)
fxx = 455 kHz)
Figure 7-3. Reset Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| S3P7048-QZ | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP42 |
| S3P72B9-QA | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP128 |
| S3C72B5XX-QA | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP128 |
| S3P72G9XX-QX | 4-BIT, OTPROM, 4.19 MHz, MICROCONTROLLER, PQFP100 |
| S3P72N8-QW | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S3C2400 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:RISC MICROPROCESSOR |
| S3C2410A | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:32-Bit RISC Microprocessor |
| S3C2410A-20 | 制造商:Samsung Electro-Mechanics 功能描述:Microprocessor, 32 Bit, 272 Pin, Plastic, BGA |
| S3C2410A20-YO80 | 制造商:Samsung Semiconductor 功能描述: 制造商:Samsung Semiconductor 功能描述:200MHz, MMU, NAND Flash Boot Loader, ROM/SRAM/SDRAM Control, STN/TFT LCD Control, Touch Panel Control, MMC/SD Card, USB, 10bit ADC/Lead Free |
| S3C2410A20-YOR0 | 制造商:Samsung Electro-Mechanics 功能描述:Microprocessor, 32 Bit, 272 Pin, Plastic, BGA |
發布緊急采購，3分鐘左右您將得到回復。