- 您現在的位置：買賣IC網 > PDF目錄385803 > S29NS128P (Spansion Inc.) MirrorBit Flash Family PDF資料下載
參數資料
| 型號： | S29NS128P |
| 廠商： | Spansion Inc. |
| 英文描述： | MirrorBit Flash Family |
| 中文描述： | MirrorBit閃存系列 |
| 文件頁數： | 31/86頁 |
| 文件大小： | 2234K |
| 代理商： | S29NS128P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁
February 20, 2007 S29NS-P_00_A1
S29NS-P MirrorBit
TM
Flash Family
31
D a t a
S h e e t
( A d v a n c e
I n f o r m a t i o n )
Figure 6.1
Synchronous Read Flow Chart
6.3.2
Continuous Burst Read Mode
In the continuous burst read mode, the device outputs sequential burst data from the starting address given
and then wraps around to address 000000h when it reaches the highest addressable memory location. The
burst read mode continues until the system drives CE# high, or RESET= V
IL
. Continuous burst mode can
also be aborted by asserting AVD# low and providing a new address to the device.
If the address being read crosses a 128-word line boundary within the same bank, but not into a program or
erase suspended sector, as mentioned above, additional latency cycles are required as reflected by the
configuration register table (
Table 6.11
) and
Tables 6.2
–
6.9
.
If the address crosses a bank boundary while the subsequent bank is programming or erasing, the device
provides read status information and the clock is ignored. Upon completion of status read or program or erase
operation, the host can restart a burst read operation using a new address and AVD# pulse.
Write Unlock Cycles:
Address 555h, Data AAh
Address 2AAh, Data 55h
Set Configuration Registers
Command and Settings:
Address 555h, Data D0h
Address X00h, Data CR0-CR1
Load Initial Address
Address = RA
Read Initial Data
RD = DQ[15:0]
Read Next Data
RD = DQ[15:0]
Wait t
IACC
+
Programmable Wait State Setting
Wait X Clocks:
Additional Latency Due to Starting
Address, Clock Frequency, and
Boundary Crossing
End of Data
Yes
Crossing
Boundary
No
Yes
Completed
Delay X Clocks
Unlock Cycle 1
Unlock Cycle 2
RA = Read Address
RD = Read Data
Command Cycle
CR = Configuration Registers
CR13-CR11 sets initial access time
(from address latched to
valid data) from 2 to 7 clock cycles
Note: Setup Configuration Register parameters
Refer to the Latency tables.
相關PDF資料 |
PDF描述 |
|---|---|
| S29NS128P0PBJW000 | MirrorBit Flash Family |
| S29NS128P0PBJW003 | MirrorBit Flash Family |
| S29NS128P0SBJW000 | MirrorBit Flash Family |
| S29NS128P0SBJW003 | MirrorBit Flash Family |
| S29NS128PABBJW000 | MirrorBit Flash Family |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29NS128P0PBJW000 | 功能描述:閃存 128M (8MX16) 66MHz Simultaneous R/W RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S29NS128P0PBJW003 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
| S29NS128P0SBJW000 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
| S29NS128P0SBJW003 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
| S29NS128PABBJW000 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:MirrorBit Flash Family |
發布緊急采購，3分鐘左右您將得到回復。