- 您現在的位置：買賣IC網 > PDF目錄192300 > S29JL032J70TFI213 (SPANSION LLC) 2M X 16 FLASH 3V PROM, 70 ns, PDSO48 PDF資料下載
參數資料
| 型號： | S29JL032J70TFI213 |
| 廠商： | SPANSION LLC |
| 元件分類： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| 封裝： | LEAD FREE, MO-142(D)DD, TSOP-48 |
| 文件頁數： | 27/63頁 |
| 文件大?。?/td> | 1618K |
| 代理商： | S29JL032J70TFI213 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁
August 24, 2011 S29JL032J_00_05
S29JL032J
33
Data
Sheet
10.3
Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manufacturer and device codes,
and determine whether or not a sector is protected. The autoselect command sequence may be written to an
address within a bank that is either in the read or erase-suspend-read mode. The autoselect command may
not be written while the device is actively programming or erasing in another bank.
The autoselect command sequence is initiated by first writing two unlock cycles. This is followed by a third
write cycle that contains the bank address and the autoselect command. The bank then enters the autoselect
mode. The system may read any number of autoselect codes without reinitiating the command sequence.
Table 10.1 on page 38 shows the address and data requirements. To determine sector protection
information, the system must write to the appropriate bank address (BA) and sector address (SA). Table 8.3
on page 18 and Table 8.4 on page 20 show the address range and bank number associated with each
sector.
The system must write the reset command to return to the read mode (or erase-suspend-read mode if the
bank was previously in Erase Suspend).
10.4
Enter Secured Silicon Region/Exit Secured Silicon Region Command
Sequence
The system can access the Secured Silicon Region region by issuing the three-cycle Enter Secured Silicon
Region command sequence. The device continues to access the Secured Silicon Region until the system
issues the four-cycle Exit Secured Silicon Region command sequence. The Exit Secured Silicon Region
command sequence returns the device to normal operation. The Secured Silicon Region is not accessible
when the device is executing an Embedded Program or embedded Erase algorithm. Table 10.1 on page 38
shows the address and data requirements for both command sequences. See also Secured Silicon Region
on page 27 for further information. Note that the ACC function and unlock bypass modes are not available
when the Secured Silicon Region is enabled.
10.5
Byte/Word Program Command Sequence
The system may program the device by word or byte, depending on the state of the BYTE# pin. Programming
is a four-bus-cycle operation. The program command sequence is initiated by writing two unlock write cycles,
followed by the program set-up command. The program address and data are written next, which in turn
initiate the Embedded Program algorithm. The system is not required to provide further controls or timings.
The device automatically provides internally generated program pulses and verifies the programmed cell
margin. Table 10.1 on page 38 shows the address and data requirements for the byte program command
sequence.
When the Embedded Program algorithm is complete, that bank then returns to the read mode and addresses
are no longer latched. The system can determine the status of the program operation by using DQ7, DQ6, or
RY/BY#. Refer to Write Operation Status on page 39 for information on these status bits.
Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a
hardware reset immediately terminates the program operation. The program command sequence should be
reinitiated once that bank has returned to the read mode, to ensure data integrity. Note that the Secured
Silicon Region, autoselect, and CFI functions are unavailable when a program operation is in progress.
Programming is allowed in any sequence and across sector boundaries. A bit cannot be programmed from
“0” back to a “1.” Attempting to do so may cause that bank to set DQ5 = 1, or cause the DQ7 and DQ6
status bits to indicate the operation was successful. However, a succeeding read will show that the data is still
“0.” Only erase operations can convert a “0” to a “1.”
相關PDF資料 |
PDF描述 |
|---|---|
| S29PL032J65BFI150 | 2M X 16 FLASH 3V PROM, 65 ns, PBGA56 |
| S29PL127J70BFI000 | 8M X 16 FLASH 3V PROM, 70 ns, PBGA80 |
| S29XS064R0PBHW010 | 4M X 16 FLASH 1.8V PROM, 80 ns, PBGA44 |
| S2C3R-1-12-H | 4000 MHz - 12000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2 dB INSERTION LOSS |
| S2C5R-1-12-RC | 4000 MHz - 18000 MHz RF/MICROWAVE SGL POLE DOUBLE THROW SWITCH, 2.8 dB INSERTION LOSS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S29JL032J70TFI220 | 功能描述:閃存 32MB 閃存 3.0V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S29JL032J70TFI310 | 功能描述:閃存 32MB 閃存 3.0V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S29JL032J70TFI313 | 制造商:Spansion 功能描述: |
| S29JL032J70TFI320 | 功能描述:閃存 32Mb 3V 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| S29JL032J70TFI323 | 功能描述:閃存 32M, 3V, 70ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。