- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C60L02 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 PDF資料下載
參數資料
| 型號： | S1C60L02 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 |
| 文件頁數： | 56/102頁 |
| 文件大小： | 674K |
| 代理商： | S1C60L02 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
S1C60N02 TECHNICAL MANUAL
EPSON
49
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (A/D Converter)
If the up-counter C0–C15 becomes "0000H" due to over-
flow, the sensor side of the oscillation circuit turns on,
and the up-counter starts counting up according to the
oscillation clock on the sensor side.
The up/down counter TC0–TC15 shifts to the counting-
down mode at this point and starts counting down from
the value measured as a result of oscillation by the
reference resistance.
Timing in starting counting when oscillation is switched,
is same as Figure 4.8.3.
When the up/down counter TC0–TC15 has counted down
to "0000H", the counting operation of both counters and
CR oscillation stops, and an interrupt occurs. At the
same time, the ADRUN register is set to "0", and the A/D
converter circuit stops operation completely.
The sensor is oscillated for the same period of time as the
reference resistance is oscillated after the up/down
counter TC0–TC15 is set to "0000H" prior to A/D conver-
sion. Therefore, the difference in oscillation frequency can
be measured from the values counted by the up-counter
C0–C15.
Since the reference resistance is oscillated until the up-
counter C0–C15 overflows, an appropriate initial value
needs to be set before A/D conversion is started. If a
smaller initial value is set, a longer counting period is
possible, thereby ensuring more accurate detection.
Likewise, if the input clock of the up/down counter TC0–
TC15 is set at 65 kHz, the degree of precision is reduced.
However, since CR oscillation frequency is normally set
lower than the clock frequency of the up/down counter
TC0–TC15 to ensure accurate measurement, the up/
down counter TC0–TC15 may overflow while counting the
oscillation frequency of the reference resistance.
If an overflow occurs, CR oscillation and A/D conversion
is terminated immediately. Also in such cases, the up/
down counter indicates "0000H", and interrupt occurs.
However, it is impossible to judge whether the interrupt
has occurred due to an overflow or normal termination.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C60N04D | 4-BIT, MROM, 2 MHz, MICROCONTROLLER, UUC48 |
| S1C60N08D | 4-BIT, MROM, 0.032768 MHz, MICROCONTROLLER, UUC96 |
| S1C60N08F0A0100 | MICROCONTROLLER, PQFP100 |
| S1C621C0D | 4-BIT, MROM, 1.3 MHz, MICROCONTROLLER, UUC74 |
| S1C62480D | 4-BIT, MROM, 2.3 MHz, MICROCONTROLLER, UUC135 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C60L05 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60L08 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60L16 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60N05 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60N08 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。