- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C60L02 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 PDF資料下載
參數資料
| 型號： | S1C60L02 |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 0.08 MHz, MICROCONTROLLER, PQFP60 |
| 文件頁數： | 25/102頁 |
| 文件大?。?/td> | 674K |
| 代理商： | S1C60L02 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
S1C60N02 TECHNICAL MANUAL
EPSON
21
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Input Ports)
Input port data (0E0H)
The input data of the input port pins can be read with these
registers.
When "1" is read:
High level
When "0" is read:
Low level
Writing:
Invalid
The value read is "1" when the pin voltage of the four bits of
the input ports (K00–K03) goes high (VDD), and "0" when the
voltage goes low (VSS). These bits are reading, so writing
cannot be done.
Interrupt mask registers (0E8H)
Masking the interrupt of the input port pins can be done
with these registers.
When "1" is written:
Enable
When "0" is written:
Mask
Reading:
Valid
With these registers, masking of the input port bits can be
done for each of the four bits. After an initial reset, these
registers are all set to "0".
Interrupt factor flags (0EDH D0)
These flags indicate the occurrence of an input interrupt.
When "1" is read:
Interrupt has occurred
When "0" is read:
Interrupt has not occurred
Writing:
Invalid
The interrupt factor flag IK0 is associated with K00–K03,
respectively. From the status of these flags, the software
can decide whether an input interrupt has occurred.
These flags are reset when the software has read them.
Reading of interrupt factor flags is available at EI, but be
careful in the following cases.
If the interrupt mask register value corresponding to the
interrupt factor flags to be read is set to "1", an interrupt
request will be generated by the interrupt factor flags set
timing, or an interrupt request will not be generated.
After an initial reset, these flags are set to "0".
K00–K03
IK0
EIK00–EIK03
相關PDF資料 |
PDF描述 |
|---|---|
| S1C60N04D | 4-BIT, MROM, 2 MHz, MICROCONTROLLER, UUC48 |
| S1C60N08D | 4-BIT, MROM, 0.032768 MHz, MICROCONTROLLER, UUC96 |
| S1C60N08F0A0100 | MICROCONTROLLER, PQFP100 |
| S1C621C0D | 4-BIT, MROM, 1.3 MHz, MICROCONTROLLER, UUC74 |
| S1C62480D | 4-BIT, MROM, 2.3 MHz, MICROCONTROLLER, UUC135 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C60L05 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60L08 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60L16 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60N05 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C60N08 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。
