- 您現在的位置：買賣IC網 > PDF目錄384890 > RS5C348A-E2 (RICOH COMPANY LTD) Real-Time Clock PDF資料下載
參數資料
| 型號： | RS5C348A-E2 |
| 廠商： | RICOH COMPANY LTD |
| 元件分類： | XO, clock |
| 英文描述： | Real-Time Clock |
| 中文描述： | 0 TIMER(S), REAL TIME CLOCK, PDSO10 |
| 封裝： | 6.40 X 3.50 MM, 1.25 MM HEIGHT, 0.5 MM PITCH, SSOP-10 |
| 文件頁數： | 33/53頁 |
| 文件大?。?/td> | 452K |
| 代理商： | RS5C348A-E2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
R
×
5C348A/B
30
Course (A)
When the time count precision of each real-time clock is not to be adjusted, the crystal oscillator intended for use
with that real-time clock may have any C
L
value requiring no presetting. The crystal oscillator may be subject to
frequency variations which are selectable within the allowable range of time count precision. Several crystal
oscillators and real-time clocks should be used to find the center frequency of the crystal oscillators by the method
described in “2.2 Measurement of Oscillation Frequency” and then calculate an appropriate oscillation adjustment
value by the method described in “2.4 Oscillation Adjustment Circuit” for writing this value to the R
×
5C348A/B.
Course (B)
When the time count precision of each real-time clock is to be adjusted within the oscillation frequency variations of
the crystal oscillator plus the frequency variations of the real-time clock ICs, it becomes necessary to correct
deviations in the time count of each real-time clock by the method described in “2.4 Oscillation Adjustment Circuit”.
Such oscillation adjustment provides crystal oscillators with a wider range of allowable settings of their oscillation
frequency variations and their C
L
values. The real-time clock IC and the crystal oscillator intended for use with that
real-time clock IC should be used to find the center frequency of the crystal oscillator by the method described in
“2.2 Measurement of Oscillation Frequency” and then confirm the center frequency thus found to fall within the
range adjustable by the oscillation adjustment circuit before adjusting the oscillation frequency of the oscillation
circuit. At normal temperature, the oscillation frequency of the oscillator circuit can be adjusted by up to
approximately ±1.5ppm.
Course (C)
Course (C) together with Course (D) requires adjusting the time count precision of each real-time clock as well as
the frequency of 32.768-kHz clock pulses output from the 32KOUT pin. Normally, the oscillation frequency of the
crystal oscillator intended for use with the real-time clocks should be adjusted by adjusting the oscillation stabilizing
capacitors C
G
and C
D
connected to both ends of the crystal oscillator. The R
×
5C348A/B, which incorporate the C
G
and the C
D
, require adjusting the oscillation frequency of the crystal oscillator through its C
L
value.
Generally, the relationship between the C
L
value and the C
G
and C
D
values can be represented by the following
equation:
C
L
=C
G
×
C
D
+ C
S
where “C
S
” represents the floating capacity of the printed circuit board
C
G
+ C
D
The crystal oscillator intended for use with the R
×
5C348A/B is recommended to have the C
L
value on the order of 6
to 8pF. Its oscillation frequency should be measured by the method described in “2.2 Measurement of Oscillation
Frequency”. Any crystal oscillator found to have an excessively high or low oscillation frequency (causing a time
count gain or loss, respectively) should be replaced with another one having a smaller and greater C
L
value,
respectively until another one having an optimum C
L
value is selected. In this case, the bit settings disabling the
oscillation adjustment circuit (see “2.4 Oscillation Adjustment Circuit”) should be written to the oscillation
adjustment register.
相關PDF資料 |
PDF描述 |
|---|---|
| RS5C348B-E2 | Real-Time Clock |
| RT1710B6 | LVDS & LVPECL FPGA Terminator RoHS Compliant Parts Available |
| RT1710B7 | LVDS & LVPECL FPGA Terminator RoHS Compliant Parts Available |
| RT1720B7 | LVDS & LVPECL FPGA Terminator RoHS Compliant Parts Available |
| RT1721B6 | LVDS & LVPECL FPGA Terminator RoHS Compliant Parts Available |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RS5C348B | 制造商:RICOH 制造商全稱:RICOH electronics devices division 功能描述:4-WIRE SERIAL INTERFACE |
| RS5C348B-E2 | 制造商:RICOH 制造商全稱:RICOH electronics devices division 功能描述:Real-Time Clock |
| RS5C372A | 制造商:RICOH 制造商全稱:RICOH electronics devices division 功能描述:I2C bus SERIAL INTERFACE REAL-TIME CLOCK ICs |
| RS5C372B | 制造商:RICOH 制造商全稱:RICOH electronics devices division 功能描述:I2C-bus Serial Interface Real Time Clock (8pin SSOP) |
| RS5C372B-E1 | 制造商:RICOH 制造商全稱:RICOH electronics devices division 功能描述:I2C-bus Serial Interface Real Time Clock (8pin SSOP) |
發布緊急采購，3分鐘左右您將得到回復。