- 您現在的位置：買賣IC網 > PDF目錄384875 > R2033K-E2 (RICOH COMPANY LTD) 3 wire interface Real-Time Clock ICs PDF資料下載
參數資料
| 型號： | R2033K-E2 |
| 廠商： | RICOH COMPANY LTD |
| 元件分類： | XO, clock |
| 英文描述： | 3 wire interface Real-Time Clock ICs |
| 中文描述： | 0 TIMER(S), REAL TIME CLOCK, QCC12 |
| 封裝： | 2 X 2 MM, 1 MM HEIGHT, FFP-12 |
| 文件頁數： | 30/50頁 |
| 文件大?。?/td> | 542K |
| 代理商： | R2033K-E2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
R2033K/T
Course (A)
When the time count precision of each RTC is not to be adjusted, the quartz crystal unit intended for use in that
RTC may have any CL value requiring no presetting. The quartz crystal unit may be subject to frequency
variations which are selectable within the allowable range of time count precision. Several quartz crystal units
and RTCs should be used to find the center frequency of the quartz crystal units by the method described in
"P29
Measurement of Oscillation Frequency" and then calculate an appropriate oscillation adjustment value
by the method described in "P32
Oscillation Adjustment Circuit" for writing this value to the R2033K/T.
Course (B)
When the time count precision of each RTC is to be adjusted within the oscillation frequency variations of the
quartz crystal unit plus the frequency variations of the real-time clock ICs, it becomes necessary to correct
deviations in the time count of each RTC by the method described in " P29
Oscillation Adjustment Circuit".
Such oscillation adjustment provides quartz crystal units with a wider range of allowable settings of their
oscillation frequency variations and their CL values. The real-time clock IC and the quartz crystal unit intended
for use in that real-time clock IC should be used to find the center frequency of the quartz crystal unit by the
method described in " P29
Measurement of Oscillation Frequency" and then confirm the center frequency
thus found to fall within the range adjustable by the oscillation adjustment circuit before adjusting the oscillation
frequency of the oscillation circuit. At normal temperature, the oscillation frequency of the oscillator circuit can
be adjusted by up to approximately
±
0.5ppm.
Course (C)
Course (C) together with Course (D) requires adjusting the time count precision of each RTC as well as the
frequency of 32.768-kHz clock pulses output from the 32KOUT pin. Normally, the oscillation frequency of the
crystal oscillator intended for use in the RTCs should be adjusted by adjusting the oscillation stabilizing
capacitors CG and CD connected to both ends of the crystal oscillator. The R2033K/T, which incorporate the
CG and the CD, require adjusting the oscillation frequency of the crystal oscillator through its CL value.
Generally, the relationship between the CL value and the CG and CD values can be represented by the following
equation:
CL = (CG
×
CD)/(CG + CD) + CS where "CS" represents the floating capacity of the printed circuit board.
The crystal oscillator intended for use in the R2033K/T is recommended to have the CL value on the order of 6 to
9pF. Its oscillation frequency should be measured by the method described in " P.29
Measurement of
Oscillation Frequency ". Any crystal oscillator found to have an excessively high or low oscillation frequency
(causing a time count gain or loss, respectively) should be replaced with another one having a smaller and
greater CL value, respectively until another one having an optimum CL value is selected. In this case, the bit
settings disabling the oscillation adjustment circuit (see " P.32
Oscillation Adjustment Circuit") should be
written to the oscillation adjustment register.
Incidentally, the high oscillation frequency of the crystal oscillator can also be adjusted by adding an external
oscillation stabilization capacitor CGOUT or/and CDOUT as illustrated in the diagram below.
30
相關PDF資料 |
PDF描述 |
|---|---|
| R2033T | 3 wire interface Real-Time Clock ICs |
| R2043T | 4-wire Serial Interface |
| R2043T-E2 | 4-wire Serial Interface |
| R2043K | 4-wire Serial Interface |
| R2043K-E2 | 4-wire Serial Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| R2033T | 制造商:RICOH 制造商全稱:RICOH electronics devices division 功能描述:3 wire interface Real-Time Clock ICs |
| R2033T-E2 | 制造商:RICOH 制造商全稱:RICOH electronics devices division 功能描述:3 wire interface Real-Time Clock ICs |
| R203426000 | 功能描述:RF 連接器 SSMB(M) STR NA PCB RoHS:否 制造商:Bomar Interconnect 產品:Connectors 射頻系列:BNC 型式:Jack (Female) 極性: 觸點電鍍:Gold 阻抗: 端接類型:Solder 主體類型:Straight Bulkhead 電纜類型: |
| R203426000W | 功能描述:RF 連接器 EMB DR CI RoHS:否 制造商:Bomar Interconnect 產品:Connectors 射頻系列:BNC 型式:Jack (Female) 極性: 觸點電鍍:Gold 阻抗: 端接類型:Solder 主體類型:Straight Bulkhead 電纜類型: |
| R203553000 | 功能描述:RF 連接器 SSMB(M) STR BH SP RoHS:否 制造商:Bomar Interconnect 產品:Connectors 射頻系列:BNC 型式:Jack (Female) 極性: 觸點電鍍:Gold 阻抗: 端接類型:Solder 主體類型:Straight Bulkhead 電纜類型: |
發布緊急采購，3分鐘左右您將得到回復。