- 您現在的位置：買賣IC網 > PDF目錄224993 > R1EX25004ATA00A 512 X 8 SPI BUS SERIAL EEPROM, PDSO8 PDF資料下載
參數資料
| 型號： | R1EX25004ATA00A |
| 元件分類： | PROM |
| 英文描述： | 512 X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| 封裝： | 4.40 X 3 MM, 0.65 MM PITCH, LEAD FREE, PLASTIC, TSSOP-8 |
| 文件頁數： | 21/22頁 |
| 文件大?。?/td> | 622K |
| 代理商： | R1EX25004ATA00A |
R1EX25002Axx00A/R1EX25004Axx00A
REJ03C0357-0002 Rev. 0.02 Jan.14 .2009
page 8 of 20
Pin Function
Serial data output (Q)
This output signal is used to transfer data serially out of the device. Data is shifted out on the falling edge of serial
clock (C).
Serial data input (D)
This input signal is used to transfer data serially into the device. It receives instructions, addresses, and the data to be
written. Values are latched on the rising edge of serial clock (C).
Serial clock (C)
This input signal provides the timing of the serial interface. Instructions, addresses, or data present at serial data input
(D) are latched on the rising edge of serial clock (C). Data on serial data output (Q) changes after the falling edge of
serial clock (C).
Chip select (
S)
When this input signal is high, the device is deselected and serial data output (Q) is at high impedance. Unless an
internal write cycle is in progress, the device will be in the standby mode. Driving chip select (
S) low enables the
device, placing it in the active power mode. After power-up, a falling edge on chip select (
S) is required prior to the
start of any instruction.
Hold (
HOLD)
The hold (
HOLD) signal is used to pause any serial communications with the device without deselecting the device.
During the hold condition, the serial data output (Q) is high impedance, and serial data input (D) and serial clock (C)
are don’t care. To start the hold condition, the device must be selected, with chip select (
S) driven low.
Write protect (
W)
This input signal is used to protect the memory against write instructions. When write protect (
W) is held low, write
instructions (WRSR, WRITE) are ignored. No action on this signal can interrupt a write cycle that has already started.
相關PDF資料 |
PDF描述 |
|---|---|
| R1LP0408CSC-7LC | 512K X 8 STANDARD SRAM, 70 ns, PDSO32 |
| R1LP0408CSP-5SC | 512K X 8 STANDARD SRAM, 55 ns, PDSO32 |
| R1LV0416CBG-5SI | 256K X 16 STANDARD SRAM, 55 ns, PBGA48 |
| R1Q2A3609BBG-50RB | 4M X 9 QDR SRAM, PBGA165 |
| R1RP0408DGE-2PR | 512K X 8 STANDARD SRAM, 12 ns, PDSO36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| R1EX25004ATA00A#S0 | 功能描述:IC EEPROM 4K 5MHZ 8TSSOP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1 系列:- 格式 - 存儲器:閃存 存儲器類型:閃存 - NAND 存儲容量:4G（256M x 16） 速度:- 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP I 包裝:Digi-Reel® 其它名稱:557-1461-6 |
| R1EX25004ATA00G | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Serial Peripheral Interface 2k EEPROM 4k EEPROM |
| R1EX25004ATA00I | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Serial Peripheral Interface Electrically Erasable and Programmable Read Only Memory |
| R1EX25004ATA00I#S0 | 制造商:Renesas Electronics Corporation 功能描述:SERIAL EEPROM 4K, SPI, TSSOP8, 制造商:Renesas Electronics Corporation 功能描述:SERIAL EEPROM 4K, SPI, TSSOP8, I-GRADE - Tape and Reel 制造商:Renesas Electronics Corporation 功能描述:IC EEPROM 4KBIT 5MHZ 8TSSOP |
| R1EX25008ASA00A#S0 | 功能描述:IC EEPROM 8K 5MHZ 8SOP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1 系列:- 格式 - 存儲器:閃存 存儲器類型:閃存 - NAND 存儲容量:4G（256M x 16） 速度:- 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP I 包裝:Digi-Reel® 其它名稱:557-1461-6 |
發布緊急采購，3分鐘左右您將得到回復。