- 您現在的位置：買賣IC網 > PDF目錄9737 > QT60160-ISG QS129 (Atmel)SENSOR IC MTRX TOUCH16KEY 32-QFN PDF資料下載
參數資料
| 型號： | QT60160-ISG QS129 |
| 廠商： | Atmel |
| 文件頁數： | 2/26頁 |
| 文件大小： | 0K |
| 描述： | SENSOR IC MTRX TOUCH16KEY 32-QFN |
| 標準包裝： | 1 |
| 系列： | QMatrix™ |
| 類型： | 電容性 |
| 輸入數/鍵： | 16 鍵 |
| 分辨率（位）： | 10 b |
| 評估套件： | 可供 |
| 數據接口： | I²C，串行，SPI? |
| 電壓基準： | 外部 |
| 電源電壓： | 1.8V，3.3V，5V |
| 電流 - 電源： | 4.6mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN |
| 供應商設備封裝： | 32-QFN |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 2822 (CN2011-ZH PDF) |
| 其它名稱： | 427-1125-6 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
3 Interfaces
3.1 Introduction
The QT60xx0 can be configured to communicate either over
an I2C bus or a shift register type Serial Peripheral Interface
(SPI).
The pins A0, A1 are used to configure the type of interface
and the I2C address if this mode is used. The modes and I 2C
addresses are available as shown in Table 3.1 below.
I2C Address 117
Vdd
I2C Address 17
Vss
Vdd
I2C Address 7
Vdd
Vss
Shift Register
Vss
Interface
A0
A1
Table 3.1 Interface Details
3.2 Shift Register Output Mode
When the option jumpers are both set at Vss, the device
disables the I2C interface and instead generates output
suitable for driving a shift register.
The shift register data is output at pin 27 (SDA). The clock is
output at pin 28 (SCL). The data is clocked on the
positive-going transition of SCL. Data is transferred from the
shift registers to the latched outputs on the positive-going
transition of LATCH. An example shift register connection is
shown in Figure 3.1.
The shift register data is output over the duration of a matrix
scan, as each key is being processed, and it is latched at the
end of the scan. The overall communication time depends on
the matrix scan time.
75us min
tSDA-SCL
SDA data to SCL clock hold time
500ns min
tLATCH
LATCH pulse width
125us min
tSCH
SCL high pulse width
500ns min
tSCL
SCL low pulse width
Units
Legend
Parameter
Table 3.2 Shift Register
Figure 3.2, page 11 shows a full shift register cycle with keys
3, 10 and 15 activated. Key Scan represents the time when
the chip is measuring signal from each key. SCL, SDA and
LATCH represent their respective signals from the chip. SCL
is an active low clock output. SDA is the data output; high if
the key is in detect and low if it is not. LATCH pulses low
when the data transfer is complete.
Data output proceeds as soon as the key has been
processed. Most keys do not get processed during the key
scan. If so, these keys are processed and the data is output
after the complete key scan.
The internal settings of the device in Shift Register mode are
the default factory settings found in Table 6.2. This means the
device will operate with a Burst Length of 48 on all keys, and
a Sleep time of 125ms for example. These settings cannot be
changed in this mode.
In Shift Register mode, the CHANGE pin is inactive and
should be left open.
3.3 I
2C Port
These devices use I2C communications, in slave mode only.
The QT60160/QT60240 will only respond to the correct
address match. I2C operating parameters are as follows:
Max Data Transfer:
100KHz
Address:
7-bit
The match address is selected via pins A0 and A1. Table 3.1
shows the address selections.
The QT60160/QT60240 allows multiple byte transmissions to
provide a more efficient communication. This is particularly
useful to retrieve several information bytes at once. Every
time the host retrieves data from the QT60160/QT60240, an
internal address pointer is incremented.
Therefore, the host only needs to write the initial address
pointer of interest (the lowest address), followed by read
cycles for as many bytes as required.
lQ
10
QT60240-ISG R8.06/0906
Figure 3.1 Shift Register Output
Q0
Q2
Q3
Q4
Q5
Q6
Q7
DS
SH_CP
ST_CP
/Q7
74HC595
Outputs, keys 16 to 23
Q0
Q2
Q3
Q4
Q5
Q6
Q7
DS
SH_CP
ST_CP
/Q7
74HC595
Outputs, keys 8 to 15
Q0
Q2
Q3
Q4
Q5
Q6
Q7
DS
SH_CP
ST_CP
/Q7
74HC595
Outputs, keys 0 to 7
QT60160/60240
SDA
SCL
Latch
27
28
9
相關PDF資料 |
PDF描述 |
|---|---|
| SY100EL12ZC TR | IC DRIVER LOW IMPEDANCE 8-SOIC |
| SY100EL12ZC | IC DRIVER LOW IMPEDANCE 8-SOIC |
| SY100E416JI TR | IC LINE RCVR QUINT DIFF 28-PLCC |
| AD7148ACPZ-1500RL7 | IC CAP-TO-DGTL CONV PROG 16LFCSP |
| MS27467P9B98SA | CONN PLUG 3POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| QT60161 | 制造商:QUANTUM 制造商全稱:QUANTUM 功能描述:16 KEY QMatrix KEYPANEL SENSORS IC |
| QT60161-AS | 制造商:QUANTUM 制造商全稱:QUANTUM 功能描述:16 KEY QMatrix KEYPANEL SENSORS IC |
| QT60161B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16 KEY QMATRIX KEYPANEL SENSOR IC |
| QT60161B-A | 制造商:QUANTUM 制造商全稱:QUANTUM 功能描述:16 KEY QMATRIX KEYPANEL SENSOR IC |
| QT60161B-AS | 功能描述:SENSOR IC MTRX TOUCH16KEY 44TQFP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 觸摸屏控制器 系列:QMatrix™ 標準包裝:96 系列:- 類型:- 觸摸面板接口:- 輸入數/鍵:- 分辨率（位）:- 評估套件:* 數據接口:- 數據速率/采樣率 (SPS，BPS):- 電壓基準:- 電源電壓:- 電流 - 電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。