![](http://datasheet.mmic.net.cn/Atmel/QT60240-ISG-QS130_datasheet_106626/QT60240-ISG-QS130_2.png)
13
4.7 Setups
..............................
13
4.6 Cal All
...............................
13
4.5 Raw Data Commands
.......................
12
4.4 Report Detections for All Keys
...................
12
4.3 Reading Data From the Device
..................
12
4.2 Writing Data to the Device
.....................
12
4.1 Introduction
............................
12
4 Control Commands
........................
11
3.4 CHANGE Pin
...........................
10
3.3 I2C Port
..............................
10
3.2 Shift Register Output Mode
....................
10
3.1 Introduction
............................
10
3 Interfaces
..............................
8
2.16 Wiring
..............................
7
2.15 Sleep
..............................
7
2.14 Detection Integrators
.......................
7
2.13 Spread Spectrum Acquisitions
..................
7
2.12 Reset Input
...........................
7
2.11 Startup / Calibration Times
....................
6
2.10 Power Supply Considerations
..................
6
2.9.3 PCB Cleanliness
........................
6
2.9.2 LED Traces and Other Switching Signals
..............
6
2.9.1 Overview
...........................
6
2.9 PCB Layout, Construction
.....................
6
2.8 Key Design
............................
5
2.7 Matrix Series Resistors
......................
4
2.6 Signal Levels
...........................
4
2.5 Sample Resistors
.........................
4
2.4 Sample Capacitor Saturation
...................
3
2.3 Cs Sample Capacitor Operation
..................
3
2.2 Burst Paring
............................
3
2.1 Matrix Scan Sequence
.......................
3
2 Hardware and Functional
.....................
3
1.3 Enabling / Disabling Keys
.....................
3
1.2 Part Differences
..........................
3
1.1 Introduction
............................
3
1 Overview
...............................
25
7.8 Moisture Sensitivity Level (MSL)
..................
25
7.7 Marking
..............................
25
7.6 Mechanical Dimensions
......................
24
7.5 Power Consumption
........................
23
7.4 Timing Specifications
.......................
23
7.3 DC Specifications
.........................
23
7.2 Recommended Operating Conditions
...............
23
7.1 Absolute Maximum Electrical Specifications
............
23
7 Specifications
...........................
21
6.16 Setups Block
..........................
20
6.15 Drift Hold Time - DHT
......................
20
6.14 Awake Timeout - AWAKE
....................
20
6.13 Wake on Key Touch - WAKE
...................
20
6.12 Sleep Duration - SLEEP
.....................
19
6.11 Mains Sync - MSYNC
......................
19
6.10 Oscilloscope Sync - SSYNC
...................
19
6.9 Adjacent Key Suppression - AKS
.................
19
6.8 Burst Length - BL
.........................
18
6.7 Positive Recalibration Delay - PRD
................
18
6.6 Negative Recal Delay - NRD
....................
18
6.5 Detect Integrators - NDIL, FDIL
..................
17
6.4 Drift Compensation - NDRIFT, PDRIFT
..............
17
6.3 Positive Threshold - PTHR
....................
17
6.2 Negative Threshold - NTHR
....................
17
6.1 Introduction
............................
17
6 Setups
................................
16
5.6 Combining Address and Data Packets Into a Transmission
....
15
5.5 Data Packet Format
........................
15
5.4 Address Packet Format
......................
15
5.3 START and STOP Conditions
...................
15
5.2 Transferring Data Bits
.......................
15
5.1 Interface Bus
...........................
15
5 I2C Operation
............................
lQ
2
QT60240-ISG R8.06/0906
Contents