- 您現在的位置：買賣IC網 > PDF目錄368231 > PSD611E1 Field Programmable Microcontroller Peripherals with Embedded Micro--Cell(可編程邏輯，4K位SRAM,26個可編程I/O,通用PLD有63個輸入) PDF資料下載
參數資料
| 型號： | PSD611E1 |
| 英文描述： | Field Programmable Microcontroller Peripherals with Embedded Micro--Cell(可編程邏輯，4K位SRAM,26個可編程I/O,通用PLD有63個輸入) |
| 中文描述： | 現場可編程微控制器外圍設備和嵌入式微-細胞（可編程邏輯，4K的位的SRAM，26我個可編程輸入/輸出，通用PLD的有63個輸入） |
| 文件頁數： | 41/84頁 |
| 文件大小： | 426K |
| 代理商： | PSD611E1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
PSD6XX Family
11-41
I/O Ports
(cont.)
Control
Register Register Register
Setting
Setting
0
1=output,
0=input
(Note 1)
Direction
VM
Defined In
PSDabel
Declare pins only
Defined In
PSDconfiguration
NA
Mode
MCU I/O
Setting
NA
PLD I/O
Logic equations
NA
NA*
(Note 1)
NA
Data Port
(Port A,B)
NA
Specify bus type
NA
NA
NA
Address Out
(Port A,B)
Declare pins only
NA
1
1 (Note 1)
NA
Address In
(Port A,B,C)
Logic equation for
Input Micro
Cells
NA
NA
NA
NA
Peripheral I/O Logic equations
(Port A)
(PSEL0 & 1)
NA
NA
NA
PIO bit =1
Table 22. Port Operating Mode Settings
*
NA – Not Applicable
NOTE 1: The direction of the Port A, B, C pins are controlled by the Direction Register ORed with the individual
output enable product term (.oe) from the GPLD AND array.
PLD I/O Mode
The PLD I/O mode uses the port as an input to the GPLD Input Micro
Cell, and/or as an
output from the GPLD, ECSPLD. The Port assignments are shown in Tables 9 and 10. The
output can be tri-stated with a control signal defined by a product term (.oe) from the
PLD, or, by setting a zero in the Direction Register. The Direction Register
must not
be set
to “1” if the pin is defined as a PLD input pin. The PLD I/O mode is specified in PSDabel by
declaring the port pins, then writing an equation assigning it to the port.
MCU I/O Mode
In the MCU I/O Mode the microcontroller uses the PSD6XXE1 ports to expand its own I/O
ports. The ports on the PSD6XXE1 are mapped into the microcontroller address space.
The addresses of the ports are listed in Table 27.
A port pin will be put into MCU I/O mode by writing a zero to the corresponding bit in the
Control Register. The direction may be changed by writing to the Direction Register for
the port where a “1” makes it an output and a “0” an input. The output enable product
term also can change the direction of the pin (see Table 19 and 20). When the pin is
configured as output, the content of the Data Out Register drives the pins. In input mode,
the microcontroller reads the port input through the Data In buffer
Ports C and D do not have a Control Register and are in MCU I/O mode by default for pins
that are not configured as PLD I/O.
Address Out Mode
For microcontrollers with a multiplexed address/data bus, the ports in Address Out mode
drive latched addresses to external devices. Address [7:0] are always assigned to Port A.
See Table 28 for the address output pin assignments on Ports A and B. The Direction
Register and the Control Register must be set to a “1” for port pins using Address Out
mode.
In non-multiplexed 8 bit bus mode, address[7:0] are available on Port B in Address Out
Mode.
Port Operating Modes
(cont.)
相關PDF資料 |
PDF描述 |
|---|---|
| PSD601E1 | Field Programmable Microcontroller Peripherals with Embedded Micro--Cell(可編程邏輯，4K位SRAM,26個可編程I/O,通用PLD有63個輸入) |
| PSD602E1 | Field Programmable Microcontroller Peripherals with Embedded Micro--Cell(可編程邏輯，4K位SRAM,26個可編程I/O,通用PLD有63個輸入) |
| PSD603E1 | Field Programmable Microcontroller Peripherals with Embedded Micro--Cell(可編程邏輯，4K位SRAM,26個可編程I/O,通用PLD有63個輸入) |
| PSD612E1 | Field Programmable Microcontroller Peripherals with Embedded Micro--Cell(可編程邏輯，4K位SRAM,26個可編程I/O,通用PLD有63個輸入) |
| PSD613E1 | Field Programmable Microcontroller Peripherals with Embedded Micro--Cell(可編程邏輯，4K位SRAM,26個可編程I/O,通用PLD有63個輸入) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PSD611E1-15J | 制造商:WSI 功能描述: 制造商:WSI 功能描述:32K X 8 OTPROM, 26 I/O, PIA-GENERAL PURPOSE, PQCC52 |
| PSD611E1-15L | 制造商:WSI 功能描述: |
| PSD611E1-70L | 制造商:WSI 功能描述: |
| PSD6121212 | 制造商:TDK-Lambda Corporation 功能描述:DC/DC,DUAL-OUT,12/-12V,0.25/-0.25A,6W - Bulk |
| PSD6-12-1212 | 功能描述:DC/DC轉換器 6W 12V 0.25A RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。