參數資料
型號： PIC16F785
廠商： Microchip Technology Inc.
英文描述： 20-Pin Flash-Based 8-Bit CMOS Microcontroller with Two-Phase Asychronous Feedback PWM, Dual High-Speed Comparators and Dual Operational Amplifiers
中文描述： 20引腳基于閃存的8兩相異步反饋的PWM，雙高位CMOS微控制器的高速比較器和雙運算放大器
文件頁數： 121/178頁
文件大小： 1620K
代理商： PIC16F785
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁當前第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁
2004 Microchip Technology Inc.
Preliminary
DS41249A-page 119
PIC16F785
15.7
Power-Down Mode (Sleep)
The Power-down mode is entered by executing a
SLEEP
instruction.
If the Watchdog Timer is enabled:
WDT will be cleared but keeps running.
PD bit in the Status register is cleared.
TO bit is set.
Oscillator driver is turned off.
I/O ports maintain the status they had before
SLEEP
was executed (driving high, low or high-
impedance).
For lowest current consumption in this mode, all I/O
pins should be either at V
DD
or V
SS
, with no external
circuitry drawing current from the I/O pin, and all
unused peripheral modules should be disabled. Digital
I/O pins that are high-impedance inputs should be
pulled high or low externally to avoid switching currents
caused by floating inputs. The T0CKI input should also
be at V
DD
or V
SS
for lowest current consumption. The
contribution from on-chip pull-ups on PORTA should be
considered.
The MCLR pin must be at a logic high level.
15.7.1
WAKE-UP FROM SLEEP
The device can wake-up from Sleep through one of the
following events:
1.
2.
3.
External Reset input on MCLR pin
Watchdog Timer Wake-up (if WDT was enabled)
Interrupt from RA2/AN2/T0CKI/INT/C1OUT pin,
PORTA change or a peripheral interrupt.
The first event will cause a device Reset. The two latter
events are considered a continuation of program exe-
cution. The TO and PD bits in the Status register can be
used to determine the cause of device Reset. The PD
bit, which is set on power-up, is cleared when Sleep is
invoked. TO bit is cleared if WDT Wake-up occurred.
The following peripheral interrupts can wake the device
from Sleep:
1.
TMR1 interrupt. Timer1 must be operating as an
asynchronous counter.
CCP Capture mode interrupt
A/D conversion (when A/D clock source is RC)
EEPROM write operation completion
Comparator output changes state
Interrupt-on-change
External Interrupt from INT pin
2.
3.
4.
5.
6.
7.
Other peripherals cannot generate interrupts since,
during Sleep, no on-chip clocks are present.
When the
SLEEP
instruction is being executed, the next
instruction (PC + 1) is pre-fetched. For the device to
wake-up through an interrupt event, the corresponding
interrupt enable bit (and PIE bit where applicable) must
be set (enabled). Wake-up is regardless of the state of
the GIE bit. If the GIE bit is clear (disabled), the device
continues execution at the instruction after the
SLEEP
instruction. If the GIE bit is set (enabled), the device
executes the instruction after the
SLEEP
instruction,
then branches to the interrupt address (0004h). In
cases where the execution of the instruction following
SLEEP
is not desirable, the user should have a
NOP
after the
SLEEP
instruction.
The WDT is cleared when the device wakes up from
Sleep, regardless of the source of wake-up.
15.7.2
WAKE-UP USING INTERRUPTS
When global interrupts are disabled (GIE cleared) and
any interrupt source has both its interrupt enable bit
and interrupt flag bit set, one of the following will occur:
If the interrupt occurs
before
the execution of a
SLEEP
instruction, the
SLEEP
instruction will
complete as a
NOP
. Therefore, the WDT and WDT
prescaler and postscaler (if enabled) will not be
cleared, the TO bit will not be set and the PD bit
will not be cleared.
If the interrupt occurs
during or after
the execu-
tion of a
SLEEP
instruction, the device will
immediately wake-up from Sleep. The
SLEEP
instruction will be completely executed before the
wake-up. Therefore, the WDT and WDT prescaler
and postscaler (if enabled) will be cleared, the TO
bit will be set, and the PD bit will be cleared.
Even if the flag bits were checked before executing a
SLEEP
instruction, it may be possible for flag bits to
become set before the
SLEEP
instruction completes. To
determine whether a
SLEEP
instruction executed, test
the PD bit. If the PD bit is set, the
SLEEP
instruction
was executed as a
NOP
.
To ensure that the WDT is cleared, a
CLRWDT
instruction
should be executed before a
SLEEP
instruction.
Note:
It should be noted that a Reset generated
by a WDT time out does not drive MCLR
pin low.
Note:
If the global interrupts are disabled (GIE is
cleared), but any interrupt source has both
its interrupt enable bit and the correspond-
ing interrupt flag bits set, the device will
immediately wake-up from Sleep. The
SLEEP
instruction is completely executed.
相關PDF資料
PDF描述
PIC16F818 18/20-Pin Enhanced FLASH Microcontrollers with nanoWatt Technology(18/20引腳，納瓦技術增強FLASH微控制器)
PIC16F819 18/20-Pin Enhanced FLASH Microcontrollers with nanoWatt Technology(18/20引腳，納瓦技術增強FLASH微控制器)
PIC16F83 8-Bit CMOS Flash/EEPROM Microcontollrs(每個I/O口有20mA吸收,25mA驅動，64字節數據EEPROM，2.0V的微控制器)
PIC16F84 18-pin Flash/EEPROM 8-Bit Microcontrollers
PIC16F85 18/20 Pin, 8-Bit CMOS FLASH Microcontroller with Comparators and A/D Product Brief
相關代理商/技術參數
參數描述
PIC16F785-E/ML 功能描述:8位微控制器 -MCU 3.5 KB 128 RAM 18I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16F785-E/P 功能描述:8位微控制器 -MCU 14KB 368 RAM 33 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16F785-E/SO 功能描述:8位微控制器 -MCU 3.5KB FL 128R 18 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16F785-E/SS 功能描述:8位微控制器 -MCU 3.5KB FL 128R 18 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16F785-I/ML 功能描述:8位微控制器 -MCU 3.5 KB 128 RAM 18I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*