- 您現在的位置：買賣IC網 > PDF目錄10905 > PIC14000T-20I/SO (Microchip Technology)IC MCU OTP 4KX14 A/D 28SOIC PDF資料下載
參數資料
| 型號： | PIC14000T-20I/SO |
| 廠商： | Microchip Technology |
| 文件頁數： | 90/153頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU OTP 4KX14 A/D 28SOIC |
| 標準包裝： | 1,600 |
| 系列： | PIC® 14 |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 20MHz |
| 連通性： | I²C |
| 外圍設備： | POR，溫度傳感器，WDT |
| 輸入/輸出數： | 20 |
| 程序存儲器容量： | 7KB（4K x 14） |
| 程序存儲器類型： | OTP |
| RAM 容量： | 192 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 6 V |
| 數據轉換器： | 斜率 A/D |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁當前第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁
1996 Microchip Technology Inc.
Preliminary
DS40122B-page 41
PIC14000
7.0
INTER-INTEGRATED CIRCUIT
SERIAL PORT (I2C
)
The I2C module is a serial interface useful for
communicating with other peripheral or microcontroller
devices. These peripheral devices may be serial
EEPROMs,
shift
registers,
display
drivers,
A/D
converters, etc. The I2C module is compatible with the
following interface specications:
Inter-Integrated Circuit (I2C)
System Management Bus (SMBus)
This section provides an overview of the Inter-IC(I2C)
bus. The I2C bus is a two-wire serial interface
developed by the Philips Corporation. The original
specication, or standard mode, was for data transfers
of up to 100 Kbps. An enhanced specication, or fast
mode, supports data transmission up to 400 Kbps.
Both standard mode and fast mode devices will
inter-operate if attached to the same bus.
The I2C interface employs a comprehensive protocol to
ensure reliable transmission and reception of data.
When transmitting data, one device is the “master”
(generates the clock) while the other device(s) acts as
the “slave”. All portions of the slave protocol are
implemented in the I2C module’s hardware, except
general call support, while portions of the master proto-
col will need to be addressed in the PIC14000 soft-
ware.
denes
some
of
the
I2C
bus
terminology. For additional information on the I2C inter-
face specication, please refer to the Philips Corpora-
tion document
“The I 2C-bus and How to Use It”.
Note:
The I2C module on PIC14000 only
supports I2C mode. This is different from
the
standard
module
used
on
the
PIC16C7X family, which supports both
I2C and SPI modes. Caution should be
exercised to avoid enabling SPI mode on
the PIC14000.
In the I2C interface protocol each device has an
address. When a master wishes to initiate a data
transfer, it rst transmits the address of the device that
it wishes to talk to. All devices “l(fā)isten” to see if this is
their address. Within this address, a bit species if the
master wishes to read from or write to the slave device.
The master and slave are always in opposite modes
(transmitter/receiver) of operation during a data
transfer. They may operate in either of these two
states:
Master-transmitter and Slave-receiver
Slave-transmitter and Master-receiver
In both cases the master generates the clock signal.
The output stages of the clock (SCL) and data (SDA)
lines must have an open-drain or open-collector in
order to perform the wired-AND function of the bus.
External pull-up resistors are used to ensure a high
level when no device is pulling the line down. The
number of devices that may be attached to the I2C bus
is limited only by the maximum bus loading specica-
tion of 400 pF.
7.1
Initiating and Terminating Data
Transfer
During times of no data transfer (idle time), both the
clock line (SCL) and the data line (SDA) are pulled high
through the external pull-up resistors. The START and
STOP
determine
the
start
and
stop
of
data
transmission. The START is dened as a high to low
transition of SDA when SCL is high. The STOP is
dened as a low to high transition of SDA when SCL is
high. Figure 7-1 shows the START and STOP. The
master generates these conditions for starting and ter-
minating data transfer. Due to the denition of the
START and STOP, when data is being transmitted the
SDA line can only change state when the SCL line is
low.
FIGURE 7-1:
I2C START AND STOP CONDITIONS
S
Start
Condition
Change
of Data
Allowed
Change
of Data
Allowed
Stop
Condition
P
SDA
SCL
This document was created with FrameMaker404
相關PDF資料 |
PDF描述 |
|---|---|
| MT100SEM.R1 | DEVICE SERVER EMBEDDED 5V |
| PIC14000T-04I/SS | IC MCU OTP 4KX14 A/D 28SSOP |
| MT5600SMI-L-32.R2 | MODEM V.32BIS SRL DATA/FAX 3.3V |
| PIC12LCE518T-04/SN | IC MCU OTP 512X12 LV W/EE 8SOIC |
| VE-22R-IY-S | CONVERTER MOD DC/DC 7.5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC-1503 | 制造商:KODENSHI 制造商全稱:KODENSHI KOREA CORP. 功能描述:Photo IC(photodiode with signal processing) |
| PIC152N-A | 制造商:SELEC CONTROLS 功能描述:PROCESS INDICATOR,2 ALARMS,1/8DIN,4DIGIT,RELAY OUTPUT |
| PIC152N-B-2 | 制造商:SELEC CONTROLS 功能描述:PROCESS INDICATOR,2 ALARMS,RETRANSMISSION OUTPUT |
| PIC163F73-I/SP | 制造商:Microchip Technology Inc 功能描述:8BIT RISC - Bulk |
| PIC1655A-278 | 制造商:GI 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。