
1999 Microchip Technology Inc.
DS40139E-page 83
PIC12C5XX
13.4
DC CHARACTERISTICS:
PIC12LC508A/509A (Commercial, Industrial)
PIC12LC518/519 (Commercial, Industrial)
PIC12LCR509A (Commercial, Industrial)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise specified)
Operating temperature
0°C
≤
T
A
≤
+70°C (commercial)
–40°C
≤
T
A
≤
+85°C (industrial)
Operating voltage V
DD
range as described in DC spec Section 13.1 and
Section 13.2.
Sym
Min
Typ
Max
Units
Param
No.
Characteristic
Conditions
Input Low Voltage
I/O ports
with TTL buffer
V
IL
D030
V
SS
V
SS
V
SS
V
SS
V
SS
V
SS
-
-
-
-
-
-
0.8V
0.15V
DD
0.2V
DD
0.2V
DD
0.2V
DD
0.3V
DD
V
V
V
V
V
V
For 4.5V
≤
V
DD
≤
5.5V
otherwise
D031
D032
D033
D033
with Schmitt Trigger buffer
MCLR, GP2/T0CKI (in EXTRC mode)
OSC1 (in EXTRC mode)
OSC1 (in XT and LP)
Input High Voltage
I/O ports
with TTL buffer
Note 1
Note 1
V
IH
-
-
D040
0.25V
DD
+
0.8V
2.0V
0.8V
DD
0.8V
DD
0.7V
DD
0.9V
DD
30
-
V
DD
V
4.5V
≤
V
DD
≤
5.5V
D040A
D041
D042
D042A
D043
D070
-
-
-
-
-
V
DD
V
DD
V
DD
V
DD
V
DD
400
30
V
V
V
V
V
μ
A
μ
A
otherwise
For entire V
DD
range
with Schmitt Trigger buffer
MCLR, GP2/T0CKI
OSC1 (XT and LP)
OSC1 (in EXTRC mode)
GPIO weak pull-up current (Note 4)
MCLR pull-up current
Input Leakage Current
(Notes 2, 3)
I/O ports
Note 1
I
PUR
-
250
-
V
DD
= 5V, V
PIN
= V
SS
V
DD
= 5V, V
PIN
= V
SS
D060
I
IL
-
-
+1
μ
A
Vss
≤
V
PIN
≤
V
DD
, Pin at hi-imped-
ance
Vss
≤
V
PIN
≤
V
DD
Vss
≤
V
PIN
≤
V
DD
, XT and LP osc
configuration
D061
D063
T0CKI
OSC1
-
-
-
-
+5
+5
μ
A
μ
A
Output Low Voltage
I/O ports
D080
V
OL
-
-
0.6
V
I
OL
= 8.5 mA, V
DD
= 4.5V,
–40
°
C to +85
°
C
I
OL
= 7.0 mA, V
DD
= 4.5V,
–40
°
C to +125
°
C
D080A
-
-
0.6
V
Output High Voltage
I/O ports (Note 3)
D090
V
OH
V
DD
- 0.7
-
-
V
I
OH
= -3.0 mA, V
DD
= 4.5V,
–40
°
C to +85
°
C
I
OH
= -2.5 mA, V
DD
= 4.5V,
–40
°
C to +125
°
C
D090A
V
DD
- 0.7
-
-
V
Capacitive Loading Specs on
Output Pins
OSC2 pin
D100
COSC
2
C
IO
-
-
15
pF
In XT and LP modes when exter-
nal clock is used to drive OSC1.
D101
All I/O pins
Data in “Typ” column is at 5V, 25
°
C unless otherwise stated. These parameters are for design guidance only and are not
tested.
In EXTRC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
PIC12C5XX be driven with external clock in RC mode.
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
Negative current is defined as coming out of the pin.
This spec. applies when GP3/MCLR is configured as MCLR. The leakage current of the MCLR circuit is higher than the
standard I/O logic.
-
-
50
pF
Note 1:
2:
3:
4: