- 您現在的位置：買賣IC網 > PDF目錄3875 > PIC12C671-10/P (Microchip Technology)IC MCU OTP 1KX14 A/D 8DIP PDF資料下載
參數資料
| 型號： | PIC12C671-10/P |
| 廠商： | Microchip Technology |
| 文件頁數： | 48/129頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU OTP 1KX14 A/D 8DIP |
| 產品培訓模塊： | Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio |
| 標準包裝： | 60 |
| 系列： | PIC® 12C |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 10MHz |
| 外圍設備： | POR，WDT |
| 輸入/輸出數： | 5 |
| 程序存儲器容量： | 1.75KB（1K x 14） |
| 程序存儲器類型： | OTP |
| RAM 容量： | 128 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 3 V ~ 5.5 V |
| 數據轉換器： | A/D 4x8b |
| 振蕩器型： | 內部 |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 8-DIP（0.300"，7.62mm） |
| 包裝： | 管件 |
| 配用： | ISPICR1-ND - ADAPTER IN-CIRCUIT PROGRAMMING AC124001-ND - MODULE SKT PROMATEII 8DIP/SOIC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁
1999 Microchip Technology Inc.
DS30561B-page 25
PIC12C67X
5.0
I/O PORT
As with any other register, the I/O register can be
written and read under program control. However, read
instructions (i.e., MOVF GPIO,W) always read the I/O
pins independent of the pin’s input/output modes. On
RESET, all I/O ports are defined as input (inputs are at
hi-impedance), since the I/O control registers are all
set.
5.1
GPIO
GPIO is an 8-bit I/O register. Only the low order 6 bits
are used (GP<5:0>). Bits 6 and 7 (SDA and SCL,
respectively) are used by the EEPROM peripheral on
the PIC12CE673/674.
Refer to Section 6.0 and
Appendix B for use of SDA and SCL. Please note that
GP3 is an input only pin. The configuration word can
set several I/O’s to alternate functions. When acting as
alternate functions, the pins will read as ‘0’ during port
read. Pins GP0, GP1 and GP3 can be configured with
weak pull-ups and also with interrupt-on-change. The
interrupt on change and weak pull-up functions are not
pin selectable. If pin 4, (GP3), is configured as MCLR,
a weak pull-up is always on. Interrupt-on-change for
this pin is not set and GP3 will read as '0'. Interrupt-on-
change is enabled by setting bit GPIE, INTCON<3>.
Note that external oscillator use overrides the GPIO
functions on GP4 and GP5.
5.2
TRIS Register
This register controls the data direction for GPIO. A '1'
from a TRIS Register bit puts the corresponding output
driver in a hi-impedance mode. A '0' puts the contents
of the output data latch on the selected pins, enabling
the output buffer. The exceptions are GP3, which is
input only and its TRIS bit will always read as '1', while
GP6 and GP7 TRIS bits will read as ’0’.
Upon reset, the TRIS Register is all '1's, making all
pins inputs.
TRIS for pins GP4 and GP5 is forced to a ’1’ where
appropriate. Writes to TRIS <5:4> will have an effect
in EXTRC and INTRC oscillator modes only. When
GP4 is configured as CLKOUT, changes to TRIS<4>
will have no effect.
Note:
A read of the ports reads the pins, not the
output data latches. That is, if an output
driver on a pin is enabled and driven high,
but the external system is holding it low, a
read of the port will indicate that the pin is
low.
5.3
I/O Interfacing
The equivalent circuit for an I/O port pin is shown in
Figure 5-1 through Figure 5-5. All port pins, except
GP3, which is input only, may be used for both input
and output operations. For input operations, these
ports are non-latching. Any input must be present until
read by an input instruction (i.e., MOVF GPIO,W). The
outputs are latched and remain unchanged until the
output latch is rewritten. To use a port pin as output,
the corresponding direction control bit in TRIS must be
cleared (= 0). For use as an input, the corresponding
TRIS bit must be set. Any I/O pin (except GP3) can be
programmed individually as input or output.
serial EEPROM interface on the PIC12CE673/674.
These port pins are not available externally on the
package.
Users should avoid writing to pins GP6
(SDA) and GP7 (SCL) when not communicating with
the serial EEPROM memory. Please see Section 6.0,
EEPROM Peripheral Operation, for information on
serial EEPROM communication.
Note:
On a Power-on Reset, GP0, GP1, GP2
and GP4 are configured as analog inputs
and read as '0'.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16C56A-20I/P | IC MCU OTP 1KX12 18DIP |
| PIC18F44K20-I/MV | MCU 16KB FLASH 768B RAM 40-UQFN |
| PIC16C622A-20/P | IC MCU OTP 2KX14 COMP 18DIP |
| PIC16LF727-I/MV | MCU PIC 14KB FLASH XLP 40-UQFN |
| PIC12C672-10/P | IC MCU OTP 2KX14 A/D 8DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC12C671T | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, 8-Bit CMOS Microcontroller with A/D Converter |
| PIC12C671T-04 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, 8-Bit CMOS Microcontroller with A/D Converter |
| PIC12C671T-04/JM | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, 8-Bit CMOS Microcontroller with A/D Converter |
| PIC12C671T-04/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, 8-Bit CMOS Microcontroller with A/D Converter |
| PIC12C671T-04/SM | 功能描述:8位微控制器 -MCU 1.75KB 128 RAM 6 I/O 4MHz SOIC8 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。