- 您現在的位置：買賣IC網 > PDF目錄1960 > PI2EQX5804CNJE (Pericom)IC PCI-E REDRIVER 100LBGA PDF資料下載
參數資料
| 型號： | PI2EQX5804CNJE |
| 廠商： | Pericom |
| 文件頁數： | 20/23頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PCI-E REDRIVER 100LBGA |
| 標準包裝： | 176 |
| 系列： | ReDriver™ |
| 類型： | 轉接驅動器 |
| Tx/Rx類型： | CML |
| 電容 - 輸入： | 50pF |
| 電源電壓： | 1.15 V ~ 1.25 V |
| 電流 - 電源： | 800mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-BGA |
| 供應商設備封裝： | 100-LBGA（11x11） |
| 包裝： | 托盤 |
6
PS8926B
06/08/09
PI2EQX5804C
5.0Gbps 4-Lane PCIe 2.0 ReDriver with
Equalization & Emphasis
Output Swing Control
S1_[A:B]
S0_[A:B]
Swing (Diff. VPP)
001V
0
1
0.5V
1
0
0.7V
1
0.9V
Output De-emphasis Adjustment
D2_[A:B]
D1_[A:B]
D0_[A:B]
De-emphasis
0000dB
0
1
-2.5dB
0
1
0
-3.5dB
0
1
-4.5dB
1
0
-5.5dB
1
0
1
-6.5dB
1
0
-7.5dB
1
-8.5dB
Emphasis settings are determined by the state of the DEx_y input pins and conguration registers, as shown in
the Output De-emphasis table below. De-Emphasis is selected as the default power-on mode in following the
PCI Express specication, but can be changed to Pre-emphasis via reprogramming the Loopback and Empha-
sis Control register using the I2C interface.
Input Level Detect
An input level detect and output squelch function is provided on each channel to eliminate re-transmission of
input noise. A continuous signal level below the Vth- threshold causes the output driver to go to a high-impre-
dance state, so that both the positive and negative output signal are pulled to VDD by the internal pull-up resis-
tors. This feature supports the L0s PCI Express Electrical Idle state.
Receiver Detect
Automatic Receiver Detection is a feature that can set the number of active channels. By sensing the presence of a load
device on the output, the channel can be automatically enabled for operation. This allows the PI2EQX5804C to cong-
ure itself properly depending on the devices it is communicating with, whether it is a 4-lane, 3-lane, 2-lane or just 1-lane
device or adapter card.
Receiver Detect is enabled by the RXD_A, or RXD_B pins, or alternatively via I2C programming. When RXD_A or
RXD_B is set to low, then the Receiver Detect operation for that group of channel is disabled, and those channels go
directly to 50-Ohm input termination to ground and 50-Ohm output termination to VDD (for a valid differential channel
input level) or to 2K-Ohm (if the signal level is less than the threshold level).
(Continued)
09-0001
相關PDF資料 |
PDF描述 |
|---|---|
| PI2EQX5864CZFE | IC PCI-E REDRIVER 56TQFN |
| PI2EQX5904NJE | IC PCIE 2.0 REDRIVER 100LBGA |
| PI2EQX5964ZFE | IC PCIE 2.0 REDRIVER 56TQFN |
| PI2EQX6804-ANJE | IC REDRIVER 100LBGA |
| PI2EQX6864-AZFE | IC REDRIVER 56TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PI2EQX5804CNJEX | 功能描述:緩沖器和線路驅動器 PCI-Express Gen-2 5.0Gbps RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| Pi2EQX5804DNJE | 功能描述:緩沖器和線路驅動器 RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| PI2EQX5804DNJEX | 功能描述:緩沖器和線路驅動器 5.0Gbps 4 lane PCIe 2.0 Redriver RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| PI2EQX5864 | 制造商:PERICOM 制造商全稱:Pericom Semiconductor Corporation 功能描述:5.0Gbps 4-Lane PCI Express GenII Re-Driver with Equalization, Emphasis, &I2C Control |
| PI2EQX5864CZFE | 功能描述:緩沖器和線路驅動器 PCI express Gen-2 5.0Gbps RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。